Page 12
AutoSat GPS - GPRS video instruction manual
ENGLISH
Alarm e-mail format
If the system detects an alarm trigger, it will execute the following procedure:
1) Acquisition and memorization of an image for each camera installed.
2) Telephone call to the memorized telephone numbers that have been enabled to receive
ring only in case of alarm trigger. If one of the numbers does not reply to the ring, the
system will attempt another 2 calls after it has terminated sending the SMS messages and
e-mail.
3) Transmission of SMS to the memorized telephone numbers that have been enabled to
receive ring in case of alarm trigger. The alarm message format is as follows:
99999999-Attention, alarm X! Info GPS: speed 2 km/h;
latitude 41,7112 north; longitude 12,6284 east
.
The number 99999999 is the factory programmed “ID” of the AutoSat and X=1,2,3, is the
number of the input terminal that has triggered the alarm.
4) Transmission of alarm e-mail, with real time images and the GPS acquisition with position
and speed. On the text of the e-mail is indicated the number of the alarm trigger.
NOTE
If it is impossible to send the e-mail, an SMS message will be sent to the
memorized telephone numbers with the reason of the e-mail failure (see
paragraph 6.0. on Page 13).
4.0. HOW AutoSat FUNCTIONS WITH AN ALARM TRIGGER
ENGLISH
Page 5
AutoSat GPS - GPRS video instruction manual
To memorize the parameters of the SIM card (command "!PARA")
To transmit and receive e-mails, it is necessary to open an e-mail account for the SIM card
inserted in the AutoSat. To do this, you must contact the SIM card GSM company and
request an e-mail account to be assigned to the SIM card. After the e-mail account has
been assigned, you must send an SMS message to the AutoSat with the following
information:
-
E-mail address assigned to the SIM card (E-MAIL_SIM)
-
End user identification number for the internet connection (USERID)
-
Recognition password for connection to internet (INT_PSSW)
The SMS message will be as shown below:
!PARA#PSW#E-MAIL_SIM#USERID#INT_PASSW#
Example
: If the system password is 1234 and you obtained from the tel. Co. the USERID
"brown" and the password "test", and the e-mail address is "[email protected]",
then the SMS message that must be sent is:
!PARA#1234#[email protected]#brown#test#
The AutoSat will send an SMS confirmation reply message to the telephone number that
has made the request.
AutoSat
replies:
PARA: [email protected], brown, test
To memorize and cancel the e-mail addresses (maximum 3) (command "!
MAIL")
To memorize in the AutoSat the e-mail address (maximum 29 characters) to which you
wish to send e-mails with photo images, it is necessary to send an SMS message to the
AutoSat as shown below:
!MAIL#PSW#option#address1#address2#address3#
where: option = ‘A’ is to receive the e-mail automatically in case of alarm or by request
option = ’B’ to receive the e-mail
only
when requested
Example:
!MAIL#1234#A#[email protected]#[email protected]#[email protected]
AutoSat
replies:
MAIL:[email protected]#[email protected]#[email protected]
To cancel the e-mail addresses memorized, send the following message:
!MAIL#PSW#C
Example:
!MAIL#1234#C
3.0. MESSAGE PROGRAMMING
3.1. SMS message programming
The AutoSat may receive SMS command messages from any telephone number, but to
access, you need a password (indicated as PSW).
The unit is factory supplied with password
1234
. It is possible to change this password of the
AutoSat by sending an SMS (see paragraph 3.2. at Page 7).
