manualshive.com logo in svg

Autopilot Kanardia, Installation Manual

Share
Download
Autopilot Kanardia Installation Manual Download Page 11

Autopilot Installation Manual

1.5

Principle of Operation

ˆ

Simple RJ45 cables (a.k.a. Ethernet cables) are needed to connect them
together. The devices are communicating using the CAN bus system,
which is integral part of almost all Kanardia devices.

In this combination, Amigo is essential.

1.5

Principle of Operation

When autopilot is active, pilot selects requested altitude, direction and rate of
climb or descend. AD-AHRS-GPS device provides current values for almost
all flight parameters.

Controller units compare the requested values with

actual values and give appropriate commands to the servo motors. The PID
controller principle is used together with the cascade control system.

The autopilot drives two separate controls: aileron and elevator. In general
these two controls are independent, though minor dependency may exists.

Each control has two control loops

1

. Elevator control has pitch loop and

vertical speed loop. The two loops are regulated by cascade. This means that
requested altitude sets wanted vertical speed and the vertical speed loop sets
wanted pitch. The pitch loop then controls the elevator by minimizing the
difference between requested and actual pitch. Aileron works in a similar way.
Requested direction sets the required roll angle and the roll loop controls the
aileron trying to minimize the difference between requested and actual roll
angle.

This means that autopilot has four loops:

pitch

and

vertical speed

loops are

used for elevator, while

heading

and

roll

loops are used for aileron. All these

loops must be properly tuned to achieve requested autopilot operation. Var-
ious experimental values in the form of tuning parameters are provided at
the end of the document. These values represent good starting point for first
autopilot tests.

2

Mechanical Installation

This section provides information about the installation of autopilot servo mo-
tors (the SERU device) into an airplane. It contains important rules which

1

The control loop is basic term from control theory.

In simple terms – the control

loop tries to move the actuator in such a way that difference between WANTED and
ACTUAL value becomes minimal.

11

©

Kanardia

2016-2020

Summary of Contents for Kanardia





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands