C3-RS-601
H1 6 Pin Wht.
H2 5 Pin
H3 10 Pin White
H4
Valet
H5
ANT.
H6 DL
H7
LED
RX-300A
Valet
Switch
Violet : Starter Output
Red : 12 Volt Input
Red : 12 Volt Input
Yellow. Ignition 1 Output
Pink : Ignition 2 Output
Brown ACC Output
LED Indicator
FUSE
FUSE
Red/White : Parking light Input
FUSE
White : Parking light Output
Black : System Ground
Brown : Programmable Output (-)
Horn (-) or Factory Rearm (-)
Red : System Power + 12 Volt
Yellow : Ignition 3 Output ( 200 mA - )
Blue/Black : ACC 2 ( 200 mA - )
Pink : 200mA Programmable Output (-)
White : Ground When Running By-pass Control Output
Gray : CH 3 Trunk Release (-)
White/Violet : Safety Shutdown Brake Input (+)
Black/White : Neutral Safety Switch (-) Input
White/Black : Safety, Hood Pin Input (-)
White/Blue : Instant Start (-) Input
White/Red : Tachometer Signal Input
Blue : (-) Unlock
(+) Lock
Green : (-) Lock
(+) Unlock
Door Locks
H8
20A
20A
Red: Remote Start Power 1
Red: Remote Start Power 2
Violet: Starter (+) Output
Pink: Ignition 2 (+) Output
Yellow: Ignition 1 (+) Output
Brown: Acc/Heater (+) Output
Red:
12v + Battery Power
Brown:
Siren (+) Output
Black:
System Main Ground (-)
White:
Parking Light Relay Output
Red/White:
Parking Light Relay Power Input
FEATURE “III” PROGRAMMING:
1. Turn the Ignition 'switch
„ON/OFF‟ 3 TIMES
and stay in
OFF position
.
2. Push the Valet switch
3 times
(holding in on the 3
rd
push
) until
one
chirp with one long
chirp is heard, then release the valet switch. You are now in the Alarm feature
“A”
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
One Chirp /
LED one
pulse
Factory
Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1.
20 minutes
run time
10 minutes run
time
30 minutes run
time
5 minutes run
time
2.
0.8-second
Door lock &
Unlock.
3.5-second
Door
Lock & Unlock.
0.8 second
lock, 0.35
second unlock
0.8 second dbl
lock,0.8 second
dbl unlock
Five chirps= 0.8 second lock, dbl 0.8 second unlock
Six chirps= dbl 0.8 second lock, 0.8 second unlock
3.
+
Door Lock
before start
Door Lock after
start
Door Lock
before & after
start
* This is the
preferred setting
when using the
optional XT-11
single button
remote
Without this
feature
Exit:
Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking
light flashes will confirm exit.
FEATURE “IV” PROGRAMMING:
1. Turn the Ignition 'switch
„ON/OFF‟ 3 TIMES
and stay in
OFF position
.
2. Push the Valet switch
4 times
(holding in on the 4
th
push
) until
one
chirp with one long
chirp is heard, then release the valet switch. You are now in the Alarm feature
“A”
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
One Chirp /
LED one
pulse
Factory
Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps
/ LED four
pulse
1.
Tachometer
checking type.
Voltage checking
type
Timer checking
type
DBI TACH
**
DATA
ONLY !!
2.
RPM learning
Start Timer:
0.6-second
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4
chirps), 1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-
second (7 chirps), 2.0-second (8 chirps), 3.0-second (9
chirps), 4.0-second (10 chirps),
3.
+
Low ceck
level
Hi check level
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will
confirm exit.
FEATURE “V” PROGRAMMING:
1. Turn the Ignition 'switch
„ON/OFF‟ 3 TIMES
and stay in
OFF position
.
2. Push the Valet switch
5 times
(holding in on the 5
th
push
) until
one
chirp with one long
chirp is heard, then release the valet switch. You are now in the Alarm feature
“A”
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory
Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four
Chirps /
LED four
pulse
1.
Second
Accessory
H3/9 Blue/Black
Second Start
H3/9 Blue/Black
2.
+ 50 RPM
DBI ONLY
No RPM learning
3.
+
- 50 RPM
DBI ONLY
No RPM Learning or < 50RPM
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will
confirm exit.
C3-RS-601
QUICK START INSTALLATION GUIDE
Help Auto Page protect our environment !
If you are not proficient in the installation of this product or would
like a full version of the installation manual, Please visit our web
site @
www.autopageusa.com
FOR PROFESSIONAL INSTALLATION ONLY!
H1 6 PIN HEAVY GAUGE WIRE HARNESS
H5 5 PIN WIRE HARNESS
PROGRAMMING TRANSMITTER
Note:
This model will only retain the last 4 remote transmitters programmed. If the
transmitter memory is exceeded, the security system will start deleting transmitters from
memory in chronological order.
1.
Turn the Ignition 'switch „
OFF/ON‟ 3 TIMES
and stay in
ON
position
.
“Within 15 seconds”.
2. Push the Valet switch
2 times
and hold it on the
2
nd
push until a long chirp is heard
then release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming
chirp, indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3
for remaining transmitters.
FEATURE PROGRAMM
FEATURE “I” PROGRAMMING:
1. Turn the Ignition 'switch
„ON/OFF‟ 3 TIMES
and stay in
OFF position
.
2. Push the Valet switch
1 times
(holding in on the 1
st
push
) until
one
chirp with one
long chirp is heard, then release the valet switch. You are now in the Alarm feature
“A”
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps/
LED three pulse
1.
H3/2 White/Blue
= 1 Pulse
Remote Start
H3/2 White/Blue = 3
Pulse Remote Start
2.
H3/8 Pink Wire =
Factory Security
Disarm Signal
Output
H3/8 Pink Wire =
Start Status (Shock
Sensor Bypass
Control) Output
H3/8 Pink Wire = 20
Second Ground out
Key Sensor By-pass
3.
+
H2/4 Brown Wire
= Horn Output
H2/4 Brown Wire =
Rearm Signal Output
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking
light flashes will confirm exit.
FEATURE “II” PROGRAMMING:
1. Turn the Ignition 'switch
„ON/OFF‟ 3 TIMES
and stay in
OFF position
.
2. Push the Valet switch
2 times
(holding in on the 2
nd
push
) until
one
chirp with one
long chirp is heard, then release the valet switch. You are now in the Alarm feature
“A”
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1.
Button
Two
Push Remote
Button
One
push
Remote Start
2.
Without ignition
controlled door
locks & unlocks
Ignition
controlled
door locks &
unlocks
3.
+
Gasoline Engine
Diesel Engine
and 10 seconds
warn-up timer
Diesel Engine
and 15 seconds
warn-up timer
Diesel Engine
and 20
seconds warn-
up timer
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking
light flashes will confirm exit.
960 Knox Street Unit B
Torrance, California 90502
Main Office: 310-323-1800
Technical Support: 800-945-2527
(For Authorized Dealers Only)
www.autopageusa.com
FEATURE “V” MUST BE PROGRAMMED FOR THE
UNIT TO RESPOND TO REMOTE START!
If you are not sure or do not understand any part of
the quick start guide, please download the complete
installation
manual
available
at
www.autopageusa.com
. This quick start guide is a
brief outline for professional installers that are
familiar with the installation and operation of this
remote start system. Please test all of your
installation to insure proper operation of the vehicle
before returning it to the customer.
For authorized dealer technical support, please call
800-945-2527 and wait for the first available
technician. Technical support hours are Monday
through Saturday from 8:00 to 5:00 Pacific standard
time.
This Remote Starter with Alarm and Keyless Entry System
has been designed to be installed on fuel-injected vehicles
with an automatic transmission
ONLY.
Never install this remote starter on a manual
transmission vehicle.
This system must be installed and wired through a
safety switch so it will not start in any forward or reverse
gear.
Some automatic transmission vehicles mainly older GM
vehicles with a purple starter wire have a mechanical-type
park safety switch instead of electrical safety switch. The
mechanical type does not interrupt the starter circuit when
the transmission is in any gear and does not offer the 100%
level of safety required for remote starting purposes.
Therefore, our system should never be installed on any
vehicle that uses a mechanical type park safety switch.
Once you install this system, you must verify that the
vehicle will not start in any forward or reverse gear,
regardless of the type of vehicle.
Read the operation manual for operating.
Do not install any component near the brake, gas pedal
or steering linkage.
Some vehicles have a factory installed transponder
immobilizer system that can severely complicate the
installation. There is a possibility that this system cannot be
installed on some immobilizer-equipped vehicles.
Most vehicles have an SRS air bag system. Use
extreme care and do not probe any wires of the SRS
system.
Disconnect the car battery before beginning work on the
vehicle.
Check behind panels before drilling any holes. Ensure
that no wiring harness or other components are located
behind the panels that would otherwise be damaged.
Do not use conventional crimp lock, bullet on any wiring.
Poor wiring, i.e. taped joints will possibly introduce
unreliability into the alarm system and may result in false
alarms or incorrect operation. We suggest soldering all
connection points.
Install the wiring neatly under carpets or behind trim to
prevent possible damage to wires.
