Autonics MP5M Series, Product Manual, Page: 2 / 6

-|Transparent Guide|-
Product Components
• Product (+ bracket) • Instruction manual
Connections
• HOLD / RESET terminal function is different depending on the operation mode.
(F1 to F10: HOLD, F11 to F14: RESET)
• SOURCE: 100 - 240 VACᜠ 50 / 60 Hz 9 VA
24 VACᜠ 50 / 60 Hz 6.5 VA, 24 - 48 VDCᜡ 5 W
■ Cautions during Wiring ■ Indicator
• Unit: mm, Use terminals of size specified
below.
≥3.5
≤7.0
INA +12V INB 0V
8
1
10
3
12
5
9
2
11
4
13
6
14
7
15
17
16
SOURCE
HOLD /
RESET
■ Relay single output ■ Relay double output
INA +12 V
CONTACT OUT:
250 VACᜠ 3 A, 30 VDCᜡ 3 A
RESISTIVE LOAD
INB 0 V
HIGH
8
1
10
3
12
5
9
2
11
4
13
6
14
7
15
17
16
SOURCE
HOLD /
RESET
INA
H L
+12V
CONTACT OUT:
250 VACᜠ 3 A, 30 VDCᜡ 3 A
RESISTIVE LOAD
INB 0V HIGH LOW
8
1
10
3
12
5
9
2
11
4
13
6
14
7
15
17
16
SOURCE
HOLD /
RESET
Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics website.
14.3
11.8
75
□67.5
□72
■ Bracket ■ Panel cut-out
46 4
5
37.5 40.5
≥ 91
□68
+ 0.7
0
≥ 91
Ordering Information
This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.
MP 5 M - ❶ ❷
❶ Power supply
2: 24 VACᜠ 50 / 60 Hz, 24 - 48 VDCᜡ
4: 100 - 240 VACᜠ 50 / 60 Hz
❷ Output
N: Indicator
1: Relay single (high-limit) +
NPN open collector output
2: Relay double (high / low-limit) +
NPN open collector output
Mode Setting
RUN
[MODE] → Parameter 0 group [MODE] →
RUN
[MODE] 2 sec
→ Parameter group 01)
[MODE] 3 sec
→
01) Press [▲], [◀] key or [MODE] key for 1.5 sec after entering parameter: select parameter groups.
Parameter Setting
• Some parameters are activated / deactivated depending on the model or setting of
other parameters. Refer to the description of each parameter.
• The parameter and setting value are cross-displayed on the display part.
• If any key is not entered for 60 sec in each parameter, it returns to RUN mode.
• [MODE] key: Saves current setting value and moves to the next parameter.
[◀] key: Checks fixed value / Changes setting digits.
[▲], [◀] key: Changes setting values.
■ Parameter 0 group
Parameter Display Default Setting range
Display
condition
P0-1
Max.
monitoring
value
hPEK 99999
• Reset (PV): [◀] key for over 2 sec
P1-1 Input
op e ration
mode:
except F11,
F14
P0-2
Min.
monitoring
value
lPEK `9999
Op eration mode Measurement range
Measurement accuracy
(23 ± 5 ℃)
F1 Frequency / revolutions / speed 0.0005 Hz to 50 kHz
F.S. ± 0.05 % rdg ± 1-digit
F2 Passing speed
F3 Cycle
0.01 to max. of each time range F.S. ± 0.01 % rdg ± 1-digit
F4 Passing time
F5 Time interval
F6 Time differential
F7 Ab solute ratio
0.0005 Hz to 50 kHz F.S. ± 0.05 % rdg ± 1-digit
F8 Density
F9 Length measurement 1
0 to 99999
-
F10 Interval
F11 Accumulation
F12
Addition / subtraction -
individual input
-19999 to 99999
F13
Addition / subtraction - phase
difference input
F14 Length measurement 2 0 to 99999
Specifications
Series MP5M-□N MP5M-□1 MP5M-□2
Input signal 01)
Solid state input 1: ≤ 50 kHz (pulse width: ≥ 10 ㎲)
Solid state input 2 02) : ≤ 5 kHz (pulse width: ≥ 100 ㎲)
Contact input: ≤ 45 Hz (contact: ≥ 12 VDCᜡ 5 mA, pulse width: ≥ 11 ms)
Voltage input Input impedance: 3.9 kΩ, [H]: 4.5 - 24 VDCᜡ, [L]: 0 - 1 VDCᜡ
No-voltage input
Short-circuit impedance: ≤ 80 Ω, residual voltage: ≤ 1 VDCᜡ,
open-circuit impedance: ≥ 100 kΩ
Display method 7-segment LED (zero blanking method)
Character size W 4 × H 8 mm
Prescale 0.0001 × 10 -9 to 9.9999 × 10 9
Hysteresis - 0 to 9999 03)
Display cycle OFF
04)
, 0.05, 0.5, 1, 2, 4, 8 sec (same as update output cycle)
Display range -19999 to 99999
Contact control output Relay
Type - 1c × 1 1a × 2
Capacity -
250 VACᜠ 3 A, 30 VDCᜡ
3 A resistive load
250 VACᜠ 3 A, 30 VDCᜡ
3 A resistive load
Solid-state control output NPN open collector
Type - × 1 × 2
Capacity - ≤ 30 VDCᜡ 100 mA ≤ 30 VDCᜡ 100 mA
Approval ᜢ ᜧ ᜫ
Unit weigth (package) ≈ 168 g (≈ 243 g) ≈ 181g (≈ 256g) ≈ 190 g ( ≈ 265 g)
01) Standard duty ratio 1:1
02) Operation mode F7, F8: ≤ 1 kHz (pulse width: ≥ 500 ㎲)
03) The hysteresis setting range varies according to the decimal point setting position.
04) Only available operation mode F2, F14
AC voltage AC / DC voltage
Power supply
100 - 240 VACᜠ ᜠ ± 10 %
50 / 60 Hz
24 VACᜠ ± 10 % 50 / 60 Hz,
24 - 48 VDCᜡ ± 10 %
Power consumption ≤ 9 VA AC: ≤ 6.5 VA, DC: ≤ 5 W
External power supply ≤ 12 VDCᜡ ±10 % 80 mA
Memory retention Number of inputs: 100,000 operations (non-volatile semiconductor memory type)
Relay life cycle
Mechanical: ≥ 5,000,000 operations
Electrical: ≥ 100,000 operations (250 VACᜠ 3 A resistive load)
Insulation resistance ≥ 100 MΩ (500 VDCᜡ megger)
Dielectric strength 2,000 VACᜠ 60 Hz for 1 min
Noise immunity ± 2 kV the square wave noise (pulse width: 1㎲) by the noise simulator
Vibration
0.75 mm double amplitude at frequency of 10 to 55 Hz in each X, Y, Z
direction for 1 hour
Vibration
(malfunction)
0.5 mm double amplitude at frequency of 10 to 55 Hz in each X, Y, Z
direction for 10 min
Shock 300m / s² (≈ 30G) in each X, Y, Z direction for 3 times
Shock (malfunction) 100m / s² (≈ 30G) in each X, Y, Z direction for 3 times
Ambient temperature -10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)
Ambient humidity 35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)