manualshive.com logo in svg

Automatic Technology GDO-6v4 EasyRoller, Installation Instructions Manual

Share
Download
Automatic Technology GDO-6v4 EasyRoller Installation Instructions Manual Download Page 29

 

Owner Installation Instructions 

GDO-6v4 EasyRoller

®

29

Parameters

Button Functions

Buttons

Function

OPERATE

Opens/Stops/Closes the door
pressing & holding will close the door in the event 
of safety beam is not functioning

DOOR CODE

Codes a transmitter button for operate, vacation, 
auxiliary  and pet functions

LIGHT CODE

Codes a transmitter button for light function

FORCE MARGIN SET & OPEN

Increases the obstruction force margin setting

FORCE MARGIN SET & CLOSE

Decreases the obstruction force margin setting

FORCE MARGIN SET (then) SET

Resets the factory default force margin settings

AUTO CLOSE TIME (then) OPEN

Increases the Auto-Close delay time

AUTO CLOSE TIME (then) CLOSE

Decreases the Auto-Close delay time

AUTO CLOSE TIME (then) SET

Resets the factory default Auto-Close delay time

CLOSE (for 6 secs.)

Clears the door limits set positions. Limits then 
need to be reset

SET (then power on) & hold until all LED’s are off

Deletes control parameters excluding transmitter 
storage memory

DOOR CODE (then power on) & hold until all LED’s 
are off

Deletes all transmitter storage memory

SET & DOOR CODE (the power on) and hold until all 
LED’s are off

Deletes all control parameters and transmitter 
storage memory.

SET

Re-initialises the Opener to re-calculate force 
margin

Summary of Contents for GDO-6v4 EasyRoller





































Reviews:

No comments

Brands by name

Popular brands

Load more brands