manualshive.com logo in svg

Automated Logic InterOP8500, Technical Instructions, Page: 11 / 20

Share
Download
Automated Logic InterOP8500 Technical Instructions Download Page 11

Revised 7/10/01 • InterOP8500

11

© 2001 Automated Logic Corporation

1. Turn the Johnson panel power switch off.

2. Determine the type of signal received by 

the field termination board. Consult the 
Johnson Controls manuals if necessary. 
The InterOP8500 must be configured to 
receive the same type of input as the 
previously removed Johnson boards.

3. Set the InterOp8500 jumpers as follows:

• For RTD mode insert a jumper for the 

individual input. The jumpers are 
located along the lower right side of the 
InterOP8500 board (see Figure 13).

NOTE

NOTE

NOTE

NOTE If using a solid-state current 
switch on a digital input, the resistance 
must drop low enough for the module to 
recognize it.

• For voltage and potentiometer mode, 

remove the jumpers. (Current mode can 
be configured by adding an external 

sense resistor. For 4-20mA use a 250 
ohm resistor Figure 14). Turn the 
InterOP8500's power switch on.    

 Figure 13. Analog Input Jumpers

U nsw itched Inputs

Jum p er  in  P la ce   =
RTD   M o d e

Sw itched Inputs

Jum p e r    R e m ove d   =
V oltag e M ode

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

Grip
He re

 Figure 14. Analog Input Wiring for 4-20 mA Signal

InterOp8500

As specified by the
sensor manufacturer.

Sensor

120 VAC

XX VAC

ungrounded

Isolated

DC Power

Supply

4-20mA

Transducer

250 ohm

resistor

Connect to Analog Input

Connect to Analog Common (unswitched)

Field Termination

Board

Summary of Contents for InterOP8500





















Reviews:

No comments