background image

 ST30 Bidata Instrument

6    ST30 Bidata Service Manual   83009-2

Z171

Chapter 3.  PCB Details

3.1 PCB Setting

The ST30 Bidata and Depth instrument PCBs are the same. Therefore, it is
necessary to ensure that the PCB is correctly set after fitting to a unit.

1.

Connect the instrument to a 12 volt power supply

2.

Observe the display. If the PCB is correctly set the display will show
 speed and depth information

3.

If the display shows unintelligible information the PCB is set for use as
a depth instrument.

Note:  The PCB can be reset as a depth unit as follows.

1.

Turn the power supply to the instrument off

2.

Press and hold down all four keys

3.

Turn the power supply on and observe the display

4.

Depth and speed only information should now be displayed.

3.2 Input/Output Signals 

(refer to Figure 2 Circuit Diagram)

Wire colour

Circuit diagram

Description

reference

Red

P1/P2

+12V nominal dc supply

Yellow

P3/P4

SeaTalk data. Intermittent streams

of +12V (nominal) pulses.

Screen

P5/P6

0V supply and signal return

Red

P7

Speed transducer supply.
12V dc nominal.

Green

P8

Speed transducer – Log signal

Screen

P9

Speed transducer, 0V

Red

P10

Depth +, echoes from transducer

Black

P11

Depth, 0V

Summary of Contents for Bidata ST30











Reviews: