Teléfono INTERCOM
INTERNAL INTERCOM TELEPHONE WITH STANDARD HANDSET
Settings:
-
“General Call” Configuration (
J1
) .
o
To receive a “General Call" the J1 jumper must be set in 2-3 position. If J1 jumper does not exist or it is set in position 1-2, the
"General Call” will be ignored.
-
“Only receive” Configuration (
SWITCH7
) .
o
If the SWITCH7 of the configuration dip-switch is activated (down), this TELEPHONE can ONLY receive calls. It will not be possible
to initiate a call from this TELEPHONE.
-
“Priority” Configuration (
SWITCH8
) .
o
If the SWITCH8 of the configuration dip-switch is activated (down), this TELEPHONE will end any current conversation, setting the
line free to perform any new call.
-
MULTITONE Configuration (Up to 7 different melodies).
o
Pressing C with the TELEPHONE hung up; we can select the desired ringtone.
-
RINGTONES VOLUME Configuration (2 levels) .
o
Pressing B we can select the ringtones volume.
-
Setting The NUMBER OF RINGTONES and the ELECTRONIC CALL EXTENSION (0 to 4 ringtones)
o
See Table 1.
-
Setting AUXILIARY OUTPUT (1 second pulse or TOGGLE)
o
See Table 1.
Features:
-
STANDARD Handset.
-
DIALING with (KEY button) and handset hung up.
-
UP TO 6 TELEPHONE maximum.
-
BEEP warning if trying to codify a TELEPHONE greater than 6.
-
EVERY TELEPHONE CODIFY WITH ID=0, will always make a “General Call” with just one touch of the (KEY button) + pick the handset up.
-
CONVERSATION LENGTH: Minimum 90s. From here, the conversation can continue indefinitely, unless a third party wants to use the
line, which will cause both devices return to its standby mode. This is indicated by a short tone in the speaker during the conversation.
-
CALLS CANNOT BE RECEIVED if the handset is picked up.
Functioning:
·
STANDBY
:
o
Handset hung up and blue led ON.
·
Make a call
:
o
Keep the handset hung up, and press the KEY button as many times as indicate the TELEPHONE number you want to call.
Then,
pick the handset up
. (
i.e., Call nº3
)
§
Press three times de KEY button with the handset hung up. Verify the blue led gives you three flashes every 6
seconds. If the TELEPHONE nº3 exists, it will start to ring and the blue led will blink quickly.
§
When trying to call to codes greater than 6, the system will return to code 1 and, if the line is busy, we’ll heard a
beep in the handset, and the blue led will return to its original blue light.
o
General Call
. With the handset hung up, keep the KEY button pressed for 2s. The blue led will blink quickly and when lifting
the handset up, a call will be made to all the TELEPHONES that have the “General Call” enabled. A conversation will begin
with the first TELEPHONE that picks up.
o
If we have already pressed the KEY button and we want to return to the standby mode without performing a call, we can
press the AUX1 button, or pick up and hang up quickly, or just wait 30s. The blue led should return to its original blue light.
·
Receive a call
:
o
While the handset is hung up
, the TELEPHONE can receive calls. It will start ringing for up to 30s and the blue led will flash
quickly. We may terminate the call pressing the AUX1 button, or just lift the handset up to start the conversation. At this
point, the blue led will flash slower and we will have audio
at least for 90s
(see “CONVERSATION LENGTH” in features).
sw7:
Sw8:
Sw1 al Sw3 Código de intercomunicación 0-6
Sw1 to Sw3 Intercom code 0-6
Activado el modo de solo recepción de llamadas
“Only reception” mode activated
Recepción de llamadas “a todos” NO permitida
Broadcast call reception disabled
