AUSTRALIAN MONITOR AMIS250 Series Operating Manual Download Page 7

12. 

Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

13. 

Do not block fan intake or exhaust ports. 

Do not operate equipment on a surface or in an

environment which may impede the normal flow of air around the unit, such as a bed, rug, weathersheet,
carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the
unit should be periodically “blown free” of foreign matter.

14. 

Do not remove the cover. 

Removing the cover will expose you to potentially dangerous voltages.

There are no user serviceable parts inside.

15. 

Do not drive the inputs with a signal level greater than that required to drive equipment to full

output.

16. 

Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source, 

such as a

battery, mains source, or power supply, regardless of whether the amplifier or console is turned on or off.

17. 

Do not run the output of any amplifier channel back into another channel’s input. Do not

parallel- or series-connect an amplifier output with any other amplifier output.

Australian Monitor Audio Inc is not responsible for damage to loudspeakers for any reason.

18. 

Do not ground any red (“hot”) terminal. Never connect a “hot” (red) output to ground or to

another “hot” (red) output!

19. 

Non-use periods. 

The power cord of equipment should be unplugged from  the outlet when left unused

for a  long  period of time.

20. 

Service Information 

Equipment should be serviced by qualified service personnel when:

A. 

The power supply cord or the plug has been damaged.

B. 

Objects have fallen, or liquid has been spilled into the equipment

C. 

The equipment has been exposed to rain

D. 

The equipment does not appear to operate normally, or exhibits a marked change in performance

E. 

The equipment has been dropped, or the enclosure damaged.

Engineered in Sydney, Australia

www.australianmonitor.com

Australian Monitor Audio Inc.

PO Box 3126,
Lynnwood,
WA 98046.
Ph: 425 673 5175
Fax: 425 673 7825
E-mail: [email protected]
             [email protected]
             [email protected]

International Sales & Corporate Head Office

Private Bag 149, Silverwater NSW 1811
149 Beaconsfield Street, Silverwater NSW 2128
Australia

Summary of Contents for AMIS250 Series









Reviews: