Power Output
120 Watts RMS
Maximum Load
80 Ohms @ 100 Volts
Power Bandwidth
60Hz - 15kHz < 0.5% THD
Frequency Response
60Hz - 15kHz (± 3dB)
Total Harmonic Distortion
0.5% @ 1kHz rated power
Signal To Noise Ratio
-74dB with all controls at their centre position
Tone Controls
Bass @ 100Hz: Boost +12dB Cut -12dB; Treble @ 10kHz: Boost +9dB Cut -9dB
Inputs
Four mic/aux universal inputs with XLR female mic sockets and
dual RCA aux sockets
Input Sensitivity
Mics: 1mV @ 200 Ohms; Aux 1-3: 75mV @ 47K Ohms; Aux 4: 300mV @ 47K Ohms
Outputs
Speaker: 100, 70 Volts, 4 & 8 Ohms; Tape: 350mV @ 10K Ohms; Line: Balanced 700mV
Phantom Power
18 Volts DC on all Mic inputs (rear panel on/off switch)
Speaker Zone Selection
Speaker zone selector, switches 100V line output to 6 separate zones.
An ”all call“ switch overrides all zones.
Controls
4 input channel gain controls, 1 Bass control,1 Treble control,
1 Master gain control, 6 Speaker zone selector, 1 Speaker ”all call“ selector,
Pre-announce defeat switch, Phantom Power switch (on rear panel)
Indicators
Power ”on” LED
Power Source
AC 230/240V - 60Hz, 110V - 50Hz (special) 3 pin IEC connector
Power Consumption
250 Watts
Protection
Soft limiter for overload and overdrive protection, plus AC and DC fuses
Dimensions/Weight
88mm H x 480mm W x 330mm D (Chassis dimensions only). 12kg
Rack Mounting
Standard
Tone Generators
Built-in four tone generator module.
Includes Bell, Pre-Announce, Alert and Evac tones
Muting
Built-in VOX muting. Channels 1 and 2 will mute channels 3 and 4
Engineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (
ABN 78 001 345 482
), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia
NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233
TAS Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Fax: (08) 8352 4488 Export Enquiries: [email protected]
Website: www.australianmonitor.com.au
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The mixer amplifier shall have four universal input channels, each comprising of a balanced microphone
input with XLR female sockets and an auxiliary input using dual RCA sockets. The 100 volt line speaker
outputs should be able to be switched via a six position selector with ”all call“. A balanced XLR output to
drive additional power amplifiers shall also be provided.
The amplifier master section shall include one master gain control, two EQ controls, one with 12dB of
cut and boost at 100Hz and the other with 9dB of cut and boost and 10kHz speaker outputs shall be
transformer isolated at 100 volt, 70 volt, 4 & 8 ohms. The amplifier must be capable of delivering 120
watts RMS into an 80 inductive ohm load, with less than 0.5% distortion measured at 1kHz and with
system hum and noise less than -74dB.
The amplifier shall be an Australian Monitor Installation Series model ACM120.