Aussie Fit V-950 User Manual Download

Page: 30 / 31

This program is designed to evaluate your fitness level by measuring the time it takes you to go from a high heart rate during a work

to your resting heart rate. (This test is only for reference and is not intended for medical purposes or to treat and or diagnose medical

conditions. The heart rate reading may be inaccurate and must not be used for medical purposes.)

Before ending your work out press the recovery button, discontinue exercising, and immediately place your hands on the contact

heart rate sensors. Continue to hold the sensors for approximately 60 seconds for the evaluation to be completed. Once the

evaluation has been completed you will see a value on the display. Consult the table below for evaluation results.

Value

Recovery Heart Rate

Excellent

Very Good

Good

Satisfactory

Poor

Very Poor

Note: if a heart rate signal is not detected within 10 seconds of the start of the evaluation the evaluation will be ended.

WARNING DECAL PLACEMENT

Summary of Contents for V-950
































Search results

Summary of Contents for V-950

Reviews:

Related manuals for V-950

Brands by name

Popular brands

Aussie Fit V-950, User Manual

Search results

Summary of Contents for V-950

Reviews:

Related manuals for V-950

Brands by name

Popular brands