Aumuller M-COM, Assembly And Commissioning Instructions

Page: 4 / 4

AUMÜLLER AUMATIC GMBH
Gemeindewald 11
86672 Thierhaupten
Tel. +49 8271 8185-0
Fax +49 8271 8185-250
info@aumueller-gmbh.de
www.aumueller-gmbh.de
AUMÜLLER AUMATIC GMBH
Gemeindewald 11
86672 Thierhaupten
Tel. +49 8271 8185-0
Fax +49 8271 8185-250
info@aumueller-gmbh.de
9000003001_V2.0_KW22/16
T
ROUBLSHOOTING
T
ROUBLSHOOTING
:
Exchanging a faulty drive in the multi-drive
system:
¢ Switch off the supply voltage (24 V DC).
¢
Disconnect the connection cable from the faulty drive.
Do not remove the
M-COM
.
¢
Mount the new / repaired drive and connect it.
¢ Switch on the supply voltage (24 V DC) - in CLOSE
direction.
¢
Observe the LED reaction of the
M-COM
.
¢
Within 10 seconds the
M-COM
signals „Ready for
operation“ for the confi gured system.
¢
If the LED blinks red, an error is displayed.
¢
Reset the
M-COM
(see chapter „Reset of
M-COM
“).
¢
Check wiring and the system.
¢ Eliminate faults.
¢ Put the system - with M-COM - back into operation
(see chapter „First commissioning“) .
¢ If the LED blinks red, an error is displayed.
¢
Reset the
M-COM
(see chapter „Reset of
M-COM
“).
¢
Check wiring and the system.
¢
Eliminate faults.
¢ Put the system - with
M-COM
- back into operation
(see chapter „First commissioning“) .
No adjustment is carried out in case of ex-
change of drives with special program-
ming
(e.g. strok e, speed)!
In case of repair please order an exchange drive with the
same parameter assignment as that of the faulty drive.
!
T
ROUBLESHOOTING USING
U
NI
PC
¢
Connect the UniPC to the system (observe the
information given in the instructions for installation of
UniPC ).
¢
By UniPC determine the address of the faulty drive.
¢ Individually disconnect white wires ( WH ) of drives,
to fi nd out where the fault drive is localized.
¢
Switch off the supply voltage (24 V DC).
¢
Disconnect and replace the faulty drive.
¢
Switch on the supply voltage (24 V DC) - in CLOSE
direction.
¢
Observe the LED reaction of the
M-COM
.
¢
Within 10 seconds the
M-COM
signals „Ready for
operation“ for the confi gured system.
LED display State
0,5s - 0,5s - 3s
blinks green (per drive 1 time)
System is o.k. (can be operated)
drives identifi ed
(1 time blinks = identifi ed one drive).
LED display State
0,5s - 0,5s - 3s
blinks green (per drive 1 time)
System is o.k. (can be operated)
drives identifi ed
(1 time blinks = identifi ed one drive).
LED display State
0,5s - 0,5s - 3s
blinks red ( X- times)
When the number of the
learned drives does not coin-
cide with the number of drives
now recognized.
F
AULT
: System is
NOT
o.k.
X drives identifi ed
(1 time blinks = identifi ed one drive).
LED display State
0,5s - 0,5s - 3s
blinks red ( X- times)
When the number of the
learned drives does not coin-
cide with the number of drives
now recognized.
F
AULT
: System is
NOT
o.k.
X drives identifi ed
(1 time blinks = identifi ed one drive).
<
<
<
<