AUMA ACV 01.2 Manual Download Page 52

Page: 52 / 168

8.1.5.

Speed reduction before reaching end positions OPEN/CLOSED (soft stop in end positions)

Prior to reaching the end position, the speed can be linearly reduced within a
programmable range.

Figure 34: Example of speed reduction in end positions

Current speed in direction OPEN/CLOSE

Target speed for end positions

Speed reduction range before end positions

Activate speed reduction before reaching end positions

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Speed functions M1699

Speed adapt.prior end M1906

Speed red.pr.end pos. M1903

Default value:

Function active

Setting values:

Function not active

<Speed reduction range> function deactivated.

Function active

<Speed reduction range> function activated.

Adjust speed reduction range before reaching end position

Within this range before the end position, the current speed will be linearly reduced
to the target speed (

Targ.speed end pos. M1905

parameter).

Information

If the current speed is lower than the target speed, the speed is increased to the
target speed!

Customer settings M0041

Speed functions M1699

Speed adapt.prior end M1906

Speed red. range M1904

Default value:

5.0 %

Setting range:

0.0 ... 25.0 %

(in % before reaching the end position, in relation to

the full travel)

Set target speed before reaching end position

The actuator runs to the end position at the target speed set by means of this
parameter.

Customer settings M0041

Speed functions M1699

Speed adapt.prior end M1906

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands