AUMA ACV 01.2 Manual Download Page 20 | Manualshive

Page: 20 / 168

background image

Status bar

The status bar (first row in the display) indicates the operation mode [1], the presence
of an error [2] and the ID number [3] of the current display indication.

Figure 12: Information in the status bar (top)

[1]

Operation mode

[2]

Error symbol (only for faults and warnings)

[3]

ID number: S = Status page

Navigation support

If further details or information are available with reference to the display, the following
indications

Details

or

More

appear in the navigation support (bottom display row).

Then, further information can be displayed via the push button.

Figure 13: Navigation support (bottom)

[1]

shows list with detailed indications

[2]

shows further available information

The navigation support (bottom row) is faded out after approx. 3 seconds. Press any
push button (selector switch in position 0 (OFF)) to fade in the navigation support.

4.2.1.

Feedback signals from actuator and valve

Display indications depend on the actuator version.

Valve position (S0001)

This indication is only available if a position transmitter (potentiometer, EWG, RWG
or MWG) is installed in the actuator.

●

S0001

on the display indicates the valve position in % of the travel.

●

The bar graph display appears after approx. 3 seconds.

●

When issuing an operation command, an arrow indicates the direction
(OPEN/CLOSE).

Figure 14: Valve position and direction of operation

Reaching the preset end positions is additionally indicated via

(CLOSED) and

(OPEN) symbols.

Figure 15: End position CLOSED/OPEN reached

0%

Actuator is in end position CLOSED

100% Actuator is in end position OPEN

20

Actuator controls

Indications

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
18
19
20
21
22
...
»

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Related manuals for ACV 01.2

Brand: National Instruments Pages: 29

Brand: VAT Pages: 27

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brand: Watts Pages: 12

Brand: Lancom Pages: 8

Brand: TagMaster Pages: 28

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

Brand: Casambi Pages: 2

Diaval AF Series

Brand: Comeval Pages: 10

SMARTCONNECT SMART/REP

Brand: Zeta Alarm Systems Pages: 48

Brand: FrSky Pages: 2

Brand: Geberit Pages: 12

multicomp F144-MS-1V1C1TI6RO-3

Brand: KBR Pages: 68

Brand: Paradox Pages: 28

Brand: Mhouse Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands