background image

Important Notice

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the 
driver if the LCD panel or video monitor is used for vehicle information, system control, 
rear  or  side  observation  or  navigation.  If  the  LCD  panel  or  video  monitor  is  used  for 
television reception, video or DVD play, the LCD panel or video monitor must be installed 

,

so that these features will only function when the vehicle is in "park" or when the vehicle s 
parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that 
operates when the vehicle is in gear or when the parking brake is not applied must be 

,

installed to the rear of the driver s seat where it will not be visible, directly or indirectly, to 
the operator of the motor vehicle.

I

nstallation  of  overhead  products  requires  careful  planning  and  preparation.    Be 

extremely careful when working on a vehicle with side curtain air bags.   Do not route 
wires near any portion of the side curtain air bag assemblies.  This includes any anchor 
points in A, B, C or D pillars of the vehicle.  Routing wires in these areas or running wires 
by the side curtain air bags can prevent the side curtain air bag from fully deploying which 
can result in personal injury to vehicle occupants.  If you have any questions regarding 
wire routing in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation ensure that the ACC 
wire is fused at the point where it is connected to the vehicle ACC wiring.  Failure to do 
so can result in damage to the vehicle if a short circuit develops between the vehicle 
connection point and the mobile video product.

Important Note

The VOD10PS2 incorporates two new features: 
1) A wireless FM Modulator
2) Snap on Covers with matching Trim Rings (Shale and Pewter).

 

Select the color that matches the interior trim.

Please  be  advised  that  the  wireless  FM  modulator  will  perform  well  in  most 

applications.  However,  in  certain  applications  the  quality  of  the  wireless
signal  may  be  less  than  optimal,  resulting  in  static  or  strong  local  station
bleed thru. If this is the case, an optional relay box is available. The Audiovox part 
number is SIRSWB and it plugs into the 1/8" jack located next to the FM antenna on 
the side of the chassis. This relay box is installed between the vehicle antenna and 
the car radio to provide the best possible FM reception of the DVD player audio. 
When the SIRSWB is installed it is recommended that the wireless FM antenna that 
is plugged into the printed circuit board next to the 3.5mm jack be unplugged. 

Licensed under one or more of the following patents,
Patent NOS.   5,775,762  and  5,927,784

Summary of Contents for VOD10PS2 - Car - 16:9 Flipdown Monitor













Reviews: