Audiovox Prestige MA200C Installation Manual And Owner'S Manual Download Page 8

8

NOTE:

If the alarm issues three warnings within 15
seconds, the siren will sound a regular alarm
tone which lasts for 30 seconds.  After 30
seconds, the siren will automatically stop
and the alarm will arm itself.

OPERATING THE SYSTEM

Operation of the system is described in this section.
Sounds  that can be produced  by the alarm system
will consist of siren chirp tones or sounds from the
motorcycle horn (optional relay).  The equivalent sounds
are shown in parenthesis.  Also if an additional optional
relay was included in the package and used to flash
the parking lights, the parking light indications will be
shown in brackets [ ].
Arming the System
1. Press and release the 1 button on the keychain

transmitter.  The system will respond with one
single siren chirp or horn sound [ one flash ].

2. If the optional relay was installed to disable the

vehicle’s starter or ignition, then any unauthorized
attempt to start or drive the motorcycle will be
prevented.

3. Any light impact or slight movement to the motor-

cycle will cause the system to immediately sound
the warning chirps (3 second chirp), discouraging
any further attempts to tamper with the motorcycle.

4. Continued movement to the motorcycle will cause

the system to trigger for the complete 30 second

alarm cycle.  At the end of the cycle, the alarm will
re-arm itself, and resume monitoring the motor-
cycle.

Disarming the System
1. When you return to the motorcycle, press and

release button 2 on the keychain transmitter.  The
system will respond with two chirps or horn sounds
[ two flashes ].

2. If the optional relay was installed to disable the

vehicle’s starter or ignition, the function is deacti-
vated and the  motorcycle's  starter or  ignition  is
operational.

Disarming After an Intrusion
When disarming, if  the system responds   with  four
chirps  and three light flashes ,  you are being alerted
to the fact  that  the alarm was  triggered during your
absence. Check  the motorcycle for damage before
proceeding.
Disarming While Sounding
To disarm the system while it is sounding, Press and
Hold button #2 until the siren stops sounding.
Remote Panic Operation
The alarm can be activated via the keychain transmit-
ter to draw attention to your vehicle during an emer-
gency situation.

Summary of Contents for Prestige MA200C













Reviews: