background image

128-8615

4 of 8

COMPLETING THE INSTALLATION
NOTE: 

This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delay interior lights, and you

wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we suggest you learn the
interior light delay.
To learn the light delay, start with all doors closed:

(1) Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system.

The LED turns on solid to confirm the system entered the learn mode.

(2) Immediately open and close the door of the vehicle to initiate the dome delay.

The unit will monitor the door trigger input Positive, (Purple), and Negative, (Brown) when active.
When the dome light turns off, the unit will add 2 seconds then exit the learn mode.

(3) The LED will begin flashing the Armed indication indicating the unit has exited the learn mode and is armed.

Antenna Wire :

 Be sure to extend the thin black antenna wire to it’s full length, and cable tie into place where it cannot be damaged.

Avoid wrapping this wire around major, high current wire looms.

On-Board Shock Sensor Setting:

1. Enter the vehicle, and turn the ignition key to the “on” position.
2. Press and release the valet/override/program push button switch 3 times. Siren Chirps Once & Led Flash Once
3. Turn the ignition off than on, you will hear short chirp followed by long chirp.
4. Turn the ignition off then on, you will hear two long chirps indicating that you are in the shock adjust mode.
5. Press the lock button to increase, and the unlock button to decrease.  The siren will chirp 1-14 times 1 being lowest

and 14 being highest.  Firmly strike the bumper of the vehicle during the adjustment mode until you find the desired level for
the Full Trigger Stage.

6. Press both the lock & unlock buttons of the transmitter simultaneously until the siren emits two long siren chirps

indicating that you are in the Pre-Detect adjust stage.

7. Press the lock button to increase, and the unlock button to decrease.  The siren will chirp 1-14 times 1 being lowest

and 14 being highest.  Firmly strike the bumper of the vehicle during the adjustment mode until you find the desired level for
the Pre-Detect Stage.

Once you have achieved the desired setting, either turn the ignition off or allow 60 seconds of inactivity to expire to exit the Shock
Adjust Mode.  Exit of the shock adjust mode is indicated by the siren emitting 3 long chirps.

CAUTION: Never perform this test on the vehicle’s glass, as you may break the window.

WARNING !

Setting the sensitivity too high can cause false alarms due to noise vibrations from passing trucks and heavy
equipment. To decrease sensitivity, follow steps 1-5 above and use the trunk/key button to decrease.

Wire Dressing:

 Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape. Secure these looms

along the routing using cable ties. This will ensure that the alarm wires are not damaged by falling onto hot or sharp moving surfaces
in the vehicle.

Operation:

 Take a few moments to check off the appropriate option boxes in the owner’s manual, and to fully explain the operation

of the system to your customer.

Page 4

Summary of Contents for Prestige 128-8615









Reviews: