Audiovox ca 6552 Installation Manual Download

Page: 31 / 38

3 - Running Lights: Controls the WHITE parking light output wire during remote
start.

Steady - Parking lights constant during the remote start cycle.

Flashing - Parking lights flash at a slow pace during the remote start cycle.

4 - Tach Mode: Determines how the system monitors the engine running during
remote start.

Tach - Hard wired directly to the tach wire of the vehicle to monitor AC
voltage.

Tachless (Crank Average/Voltage) - Determines crank time by averaging the
last 8 times the vehicle was started with the key and then monitors the
change in voltage after remote start.

Hybrid (Crank Average / No Voltage) - Determines crank time by averaging
the last 8 times the vehicle was started with the key.

DBI Port - Monitors the vehicle’s tach rate through an interface module
connected to the DBI port.

5 - Voltage Level: The voltage variance for remote start when set to tachless.
(see tach mode)

HIGH - The variance in battery voltage from before the remote start
is activated to after the engine is running must be greater than 0.5 volts.

LOW - The variance in battery voltage from before the remote start
is activated to after the engine is running may be less than 0.5 volts.

6 - Crank Time: Preset output times for the PURPLE starter wire.

7 - Crank Average / Crank Time: The length of time in which the remote start
will crank the vehicle’s starter.

Crank Average - Determines crank time by averaging the last 8 times the
vehicle was started with the key.

Preset Time - Preset starter output time. (see crank time)

Summary of Contents for ca 6552






































Search results

Summary of Contents for ca 6552

Reviews:

Related manuals for ca 6552

Brands by name

Popular brands

Audiovox ca 6552, Installation Manual

Search results

Summary of Contents for ca 6552

Reviews:

Related manuals for ca 6552

Brands by name

Popular brands