Audiovox 1286002 Owner'S Manual And Installation Manual Download Page 18

TROUBLESHOOTING

An error made in operation or during installation of this product may be mistaken for a system malfunction.  Please perform
the checks described below before contacting your dealer or service facility.

No power

Magazine cannot be
installed

CD is not played

Noise, skipping, or
intermittent sound
during playback.

Possible Cause

Remedy

Symptom

Check fuses in vehicle fuse box and changer system.
Replace as necessary with fuse of same type and
rating as original.  If fuse blows again, consult with
service facility.

Check all wiring and correct as necessary.

Insert magazine in proper direction.

Load disc correctly in the magazine.

Check sound on another disc.  If sound from second
disc is OK,  first disc is defective.

Clean disc

Remove the transit screws from sides of the unit.

Set the mounting angle adjustment to the correct
position as per the installation instructions.

Blown fuse

Incorrect connection

Magazine is inserted in wrong
direction.

Disc is loaded incorrectly in magazine.

Scratches on disc or warped disc

Extremely dirty disc

Transit screws still in place

Mounting angle adjustment is not
correct.

18

Summary of Contents for 1286002





















Reviews: