This label tells you that the unit contains a Laser component. Opening the unit will expose the user to
radiation from the laser beam.
Mains supply and safety
Mains Supply:
The mains operating voltage of all Audiolab units is shown on the rear panel. If this
does not match the voltage in your area, consult your dealer.
The mains supply fuse is located on the rear panel of the unit. If it has broken, check for any obvious
cause before replacing the fuse with one of the correct rating and type. The fuse values are:
220 - 240V (UK, Korea, etc.)
T 1AL 20mm Slow Blow
100 - 120V (USA, Japan, etc)
T 1.6AL 20mm Slow Blow
The fuse is located in a slide-in carrier which also contains a
spare fuse. The fuse carrier can only be pulled out after the
IEC power cord is unplugged. When the carrier is opened the
first fuse to be seen is the spare fuse. Remove and safely
dispose of the fuse with the blown link before replacing it.
Power Cord:
An AC power cord is normally supplied with a
mains plug suitable for your area. If you have any doubts,
consult your dealer about obtaining a suitable power cord.
Class II construction double insulated. This product must not be connected to earth.
Important notice to UK users
The appliance cord is terminated with a UK approved mains plug fitted with a A fuse. If
3
the fuse
needs to be replaced, an ASTA or BSI approved BS1362 fuse rated at 5A must be used. If you need to
change the mains plug, remove the fuse and dispose of this plug safely immediately
after cutting it
from the cord.
Connecting a Mains Plug
The wires in the mains lead are coloured in accordance with the
code: Blue: NEUTRAL; Brown: LIVE: As these colours may not
correspond to the coloured markings identifying the terminals
in your plug, proceed as follows: The BLUE wire must be
connected to the terminal marked with the letter N or coloured
BLUE or BLACK. The BROWN wire must be connected to the
terminal marked with the letter L or coloured BROWN or RED.
Use only attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning:
To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture. The product must not be exposed to dripping
and splashing and no object filled with liquids such as a vase of flowers
should be placed on the product.
No naked flame sources such as candles should be placed on the product.
R
ead these instructions.
Caution:
Changes or modifications not expressly approved by the
Keep these instructions. In the event that you pass the product to a third
manufacturer could void the user's authority to operate this device.
party this instruction manual should be provided along with the product.
This equipment has been tested and found to comply with the limits for a
Heed all warnings.
Class B digitial device, pursuant to part 15 of the FCC rules. These limits
Follow all instructions.
are designed to provide reasonable protection against harmful
Do not use this apparatus near water.
interference in a residential installation. This equipment generates, uses
Clean only with dry cloth.
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
Do not block any ventilation openings.
or television reception, which can be determined by tuning the equipment
Install in accordance with the manufacturer's instructions.
off and on, the user is encouraged to try to correct the interference by one
Do not install near any heat sources such as radiators, heat registers,
or more of the following measures:
stoves, or other apparatus (including amplifiers) that produce heat.
Re-orientate or re-locate the receiving antenna. Increase the separation
Do not defeat the safety purpose of the polarized or grounding type plug.
between the equipment and the receiver. Connect the equipment into an
A polarized plug has two blades with one wider than the other. A
outlet on a circuit different from that to which the receiver is connected.
grounding type plug has two blades and a third grounding prong. The
Consult the dealer or an experienced radio/TV technician for help.
wider blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of
Important Note:
The batteries supplied with this unit should be treated
the obsolete outlet.
with care and not punctured or damaged. Used batteries should be
Protect the power cord from being walked on or pinched, particularly at
disposed of in full conformity with recycling regulations in your area.
plugs, convenience receptacles, and the point where they exit from the
NEVER dispose of batteries in a fire or in the general rubbish.
apparatus.
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ADVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE-
NE PAS OUVRIR
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
NO USER-REMOVEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
1: Statutory & Safety Information
Analogue Specifications
Digital Specifications
General Specifications
Connectors:
DAC:
Operating Temperature Range:
2 pairs RCA phono
24bit 192kHz, 5th order Sigma Delta
10ºC-40 °C (ambient)
Output Level:
Output Format:
Power Requirements:
(Depending on Region)
2.4V rms
SPDIF
50-60Hz 100 V, 110-120 V, and 220-240 V models available
Frequency Response:
Connectors:
Power Consumption:
20Hz-20Khz +/- 0.5dB
75ohm BNC, RCA phono, Optical
Less than 25W
Output Impedance:
Output Level:
Dimensions (W x H x D):
100 Ohms
550mV p-p ( nom.) ±10%
445 x 74 x 335 mm - including feet, terminals and controls
S/N Ratio:
Output Impedance:
Weight
Better than 100dBA
75 Ohms ±5%
Net: 6 kg
Shipping: 7.4 kg
Channel Balance:
Colour:
Better than ± 0.5dB @ 1 kHz
Silver
Channel Separation:
Accessories Supplied:
Better than 100dB @ 1 kHz
AC Power Cord
THD+N (at 1kHz):
Analogue Stereo RCA 2 Phono-2Phono interconnect
Less than 0.003% 20Hz-20Khz
Instruction Manual
(>-90dB/2.4V)
8000RC Remote Control with 2 x AA batteries
Audiolab reserves the right to alter design and specification
without notice.
Specification may vary for different countries.
Audiolab is a member of the International Audio Group.
3A FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
Fuse Carrier
IEC Mains Connector
6: Specifications 8000CD
