PAGE 11
EFFECT
LIST
PAGE 6
1
3
-10
dB
HI
MID
LOW
AUX1
AUX2
AUX3
AUX4
BAL
R
L
L
R
ST LINE 13/14
-15
+
15
-15
+
15
-15
+
15
0
10
0
10
0
10
0
10
L
R
PK
SIG
PFL
SUB
MAIN
10
-50
-30
-20
-15
-10
PK
SIG
13/14
0
11
12
4
2
5
6
7
8
9
10
REVERB HALL
2.0 S
2.5 S
3.0 S
4.0 S
5.0 S
6.0 S
8.0 S
01
02
03
04
05
06
07
08
10.0 S
REVERB ROOM
1.0 S
1.5 S
2.0 S
2.5 S
3.0 S
09
10
11
12
13
14
4.0 S
REVERB PLATE
1.0 S
1.5 S
2.0 S
2.5 S
3.0 S
15
16
17
18
19
20
4.0 S
AMBIENT
0.5 S
0.7 S
1.0 S
1.3 S
21
22
23
24
25
1.6 S
GATED REVERB
75 MS
100 MS
125 MS
150 MS
200 MS
26
27
28
29
30
31
300 MS
REVERSE REVERB
75 MS
100 MS
125 MS
150 MS
200 MS
32
33
34
35
36
37
300 MS
VOICE DOUBLER
60 MS
80 MS
100 MS
120 MS
38
39
40
41
42
140 MS
ECHO & ROOM
0.1/1.0 S
43
44
0.15/1.5 S
ECHO & HALL
0.2/2.0 S
0.25/2.5 S
0.3/3.0 S
0.35/3.5 S
0.4/4.0 S
45
46
47
48
49
50
0.5/5.0 S
ECHO 50% FB
100 MS
125 MS
150 MS
200 MS
250 MS
300 MS
350 MS
400 MS
500 MS
650 MS
51
52
53
54
55
56
57
58
59
60
61
800 MS
SINGLE DELAY
50 MS
100 MS
150 MS
200 MS
250 MS
300 MS
400 MS
62
63
64
65
66
67
68
69
500 MS
CHORUS FAST
&ECHO 0.1 S
70
71
72
&ROOM 1 S
CHORUS MED
&ECHO 0.2 S
73
74
75
&HALL 2 S
CHORUS SLOW
&ECHO 0.3 S
76
77
78
&HALL 4 S
FLANGER FAST
&ECHO 0.1 S
79
80
81
&ROOM 1 S
FLANGER MED
&ECHO 0.2 S
82
83
84
&HALL 2 S
FLANGER SLOW
&ECHO 0.3 S
85
86
87
&HALL 4 S
TREMOLO FAST
88
89
&ROOM 1 S
TREMOLO MED
90
91
&HALL 2 S
TREMOLO SLOW
92
93
&HALL 4 S
WAH WAH FAST
94
95
&ROOM 1 S
WAH WAH MED
96
97
&HALL 2 S
WAH WAH SLOW
98
99
&HALL 4 S
99
preset
DSP
effect
list
1
L left line input
These are two unbalanced connectors to which the left of a line level device can be
connected, the rated input level is -10dB.
Here it is convenient for selecting RCA connector or phone jack.
2
R Right line input
These are two unbalanced connectors to which the right of a line level device can be
connected, the rated input level is -10dB.
Here it is convenient for selecting RCA connector or phone jack.
3
-10dB attenuation switch
Press this knob, the input signal will be attenuated 10dB, when the input signal level is
too strong.
8
BAL
：
This knob is used for controlling the stereo signal of the channel feed to L/R buses as
some proportion to balance the stereo sound image.
HI :
4
This knob control the frequency equalizer at higher frequency point.
Max adjust range
：
15dB @ 12KHz
±
MID
:
5
This knob control the frequency equalizer at middle frequency point.
Max adjust range: ±15dB @ 2.5KHz
LOW:
6
This knob control the frequency equalizer at lower frequency point.
Max adjust range: ±15dB @ 80Hz
AUX1,AUX2,AUX3,AUX4:
7
These 4
set in front of the channel fader, so they are not dependent on the fader position.
knobs are used for controlling the signal level feed to AUX1~4 bus, these 4 parts are all
10
CHANNEL FADER
:
This fader controls the output level feed to main bus from the input channel, adjusting the volume
balance between channels. Faders of channels not in use should be pulled down.
9
SIG,PEAK
Indicador
:
These two LED indicators detect the signal level which exists at the end of the
channel but in front of the channel fader. SIG LED flashing means the channel is in
normal, and PEAK LED will be light at 6dB before clipping to remind that the signal
level is too strong to the unit will be overload.
11
PFL
:
switch
This switch allows you to monitor the signal of the input channel, the signal is
sampled in front of the channel fader, so it has nothing to do with the fader position.
12
SUB,MAIN
channel output control
:
These two switches control if the channel signal will feed to the SUB and MAIN bus
or not separately. The switch should be turned off for unused channels.
The stereo channel(B)
CONTROL PANEL
PROFESSIONAL MIXER
Serie
PAMX3
PROFESSIONAL MIXER
Serie
PAMX3
