background image

2

Quick Start Guide

Important Safety Instructions

1. 

Read these instructions.  

2. 

Keep these instructions.

3. 

Heed all warnings.

4. 

Follow all instructions.

5. 

Do not use this apparatus near water.

6. 

Clean only with a dry cloth.

7. 

Do not block any ventilation openings. Install in accordance with the 

manufacturer’s instructions.

8. 

Do not install near any heat sources such as mufflers, silencers, exhaust 

pipes, or other apparatus (including amplifiers) that produce heat.

9. 

WARNING:

 Improper installation may lead to permanent injury or death. 

Installation of the apparatus must be done with great care by qualified 

personnel, to prevent damage to fuel lines, power, and other electrical 

wiring, hydraulic brake lines, and other systems, that might compromise 

vehicle safety.

10.  P12V and Ground insulated wiring of 4 to 0 AWG to ensure 

adequate current to the amplifier.

11.   Use rubber grommets to protect wiring whenever passing wires through 

metal openings or bulkheads.

12.  Only use attachments/accessories specified by the manufacturer.
13.  Refer all servicing to qualified service personnel. Servicing is required 

when the apparatus has been damaged in any way, such as the power in-

put terminals are damaged, liquid has been spilled or objects have fallen 

into the apparatus, the apparatus has been exposed to rain or moisture, 

does not operate normally, or has been dropped.

14.  This apparatus shall not be exposed to dripping or splashing, and no 

object filled with liquids, shall be placed on the apparatus.

15.  Fuses shall be replaced only with the correct type and fuse value, and 

only when the apparatus is powered off.

16.  Exposure to high sound pressure levels may lead to permanent hearing 

loss. Take every precaution to protect your hearing.

The lightning flash with arrowhead symbol within an equilateral 

triangle is intended to alert the user to the presence of uninsulated 

“dangerous voltage” within the product’s enclosure, that may be of 

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to 

alert the user of the presence of important operating and mainte-

nance (servicing) instructions in the literature accompanying the 

appliance.

Caution: to reduce the risk of electric shock, do 

not disassemble the apparatus, other than to 

remove the top panel to access the controls. 

There are no user-serviceable parts inside. Refer 

servicing to qualified personnel.

Recycling notice: If the time comes and this apparatus has fulfilled 

its destiny, do not throw it out into the trash. It has to be carefully 

recycled for the good of mankind, by a facility specially equipped 

for the safe recycling of electronic apparatii. Please contact your 

local or state recycling leaders for assistance in locating a suitable 

nearby recycling facility. Or, contact us and we might be able to 

repair it for you.

Summary of Contents for LL-6.1200

















Reviews: