background image

20

Specifications

P250 EQ Specifications

Output Power
 

Per Channel .......... 250 Watts @ 8 Ohm, 250 Watts @ 4 Ohm , 250  Watts @ 2 Ohm

 

Bridged Mono ......................................... 500 Watts @ 8 Ohm, 500 Watts @ 4 Ohm

Signal to Noise Ratio ..............................................> 107dB (unweighted, ref full output)
Frequency Response ................................................. ±0.25 dB 20 Hz to 20 kHz, 8Ω Load
Crosstalk ............................................................................................... > 80 dB @ 1 kHz
Damping Factor ...................................................................................................... >100
Gain   ....................................................................................................................... 27 dB
Analog Input Sensitivity ....................................1 Vrms for full output, level at maximum
DAC Specifications ..........................................32 – 192 kHz sample rate, 16/24 bit depth
AC Power Requirements
 Standby ..................................................................................................... 1.5Watts
 

Idle (main power on, all channels off) ......................................................... 18 Watts

 

All channels active ..................................................................................... 24 Watts

 

All channels 1/8th rated power .................................................................... 87Watts

 

Full Power ................................................................................................ 591 Watts

BTU/hr Output 
 Standby .................................................................................................. 5.1 BTU/hr
 

Idle (main power on, all channels off) ....................................................... 61 BTU/hr

 

All channels active ................................................................................... 82 BTU/hr

 

All channels 1/8th rated power ............................................................... 108 BTU/hr

 

Full Power (20A residential service limited) ............................................ 268 BTU/hr

Dimensions
 Height ......................................................................................................1.75

"

 (1U)

 

Width (ears on) ............................................................................................... 19.0

"

 

Width (ears off) ................................................................................................17.0

"

 Depth .............................................................................................................. 13.5

"

 Weight ............................................................................................................ 15 lbs

Please note: Because of AudioControl’s bold and daring quest to push back the frontiers of 
audio perfection, all specifications are subject to change without notice, and at any time, 
including (and not limited to) breaktime, lunchtime, and afternoon tea in engineering. 

Summary of Contents for ARCHITECT P250 EQ

























Reviews: