AudioCodes Mediant Configuration Note Download Page 11

Configuration Note 

 

3. VLANs 

Version 6.8 

11 

Mediant MSBR 

VLANs 

A  VLAN is a broadcast domain that is created by switches. Typically, it is the router that 
connects between the switches that broadcast to the VLAN domain. 

The VLAN represents a group of hosts with a common set of requirements, independent of 
a  physical location. VLANs have the same attributes as a physical LAN, but allow you to 
group end stations even if they are not located physically on the same LAN segment. 

VLANs are usually associated with IP sub-networks. For example, all the end stations in a 
particular IP subnet belong to the same VLAN. Traffic between VLANs must be routed. 
LAN port VLAN membership is assigned manually on a port-by-port basis. 

While configuring switch ports in a VLAN other than 1 (the default VLAN),  all ports in a 
single VLAN reside in the same broadcast domain. 

VLANs  are broadcast domains defined within switches to allow control of broadcast, 
multicast, unicast, and unknown unicast within a Layer 2 device. 

3.1 

Commands 

The table below describes how to assign an interface to a specific VLAN. 

Table 

 

3-1: VLAN Commands 

Command 

Description 

MSBR# configure data 

Enter the data configuration menu. 

(config-data)# interface 
<physical_interface>  
[slot/port.vlanID]

 

Allows you to enter a specific interface 
configuration mode.  

 

<physical_interface> - selects the type of 
interface. 

 

[slot/port.vlanID] – slot and port number is 
taken from the device panel. 

Note

: The interface configuration mode 

changes after the command is entered. 

(conf-if-GE SlotNum/PortNum)# 
Switchport mode access 

Sets the port into access mode. 

(conf-if-GE SlotNum/PortNum)# 
switchport access vlan 
[Vlan_ID] 

Changes the VLAN membership of the port 
from default to the VLAN ID it will use. 

Summary of Contents for Mediant

































Reviews: