background image

Features

AX303P

Blue acrylic protective cover

2-way input source and 3-way output ports

Remote power on/off by remote turn-on

Remote control for Q-factor and subwoofer level control

DC to DC switching power supply.

Fully adjustable subwoofer mid, and high-pass output levels

Stereo / Mono mode switch

Variable bass boost frequency

Infinitely variable subwoofer, mid-range and high-pass crossover

Band-pass / high-pass switch on mid-range

Phase shift switch

In / Out switch

Built-in power protection fuse (3A)

Automatic ON/OFF DC power control with radio or tape player

Frequency multiplier (1x , 10x) on high-pass output

Specifications

Adjustable bass boost and bass frequency (25Hz - 250Hz)

Q-factor: 20-2 (variable)

Selectable crossover frequency

 -Subwoofer 

(Low-pass): 

40Hz 

400Hz

 

-Mid high-pass: 40Hz - 800 Hz

 

-Mid low-pass: 2kHz - 7kHz

 

-High-pass: 40Hz - 8kHz

Power supply: 10 - 16V DC negative ground

Input impedance: 10K ohm

S/N ratio: > 85dB

Slope rate: 18dB/octave

Max input level : 7V RMS

Channel Separation: 65dB

THD: Less then 0.05%

Dimensions: 9.3" (W) x 2.2" (H) x 5.9" (D)

Summary of Contents for AX303P
















Reviews: