SYSTEM OPERATION
(I)
HANDHELD MICROPHONE SYSTEM
1. Set the antennas at an angle 45° from the floor and 90° away from each other to achieve the best RF
reception.
2. Connect the AWR6032U receiver DC input to an AC power source via the supplied AC/DC adapter.
3. Connect the AWR6032U receiver audio output to the microphone input of a mixer via the supplied audio cable
or any other appropriate cable. (Note: There are two outputs: one unbalanced output and one balanced
output.)
4.
Place one 9V battery into the battery housing of the AWX6030 microphone with the battery polarity oriented
as indicated.
5.
Turn on the power of the AWR6032U receiver. The Power On LED light will be turned on.
6.
On the AWX6030, the On/Off switch has three positions: “ON”, “MUTE” and “OFF”. When the On/Off switch is
turned to the “MUTE” or directly to the “ON” position, the low battery LED indicator will blink once and then
stay off. If the low battery LED indicator stays on, the 9V battery needs to be replaced. When the On/Off
switch is set to the “MUTE” or “ON” position, the corresponding channel 1 RF LED light or channel 2 RF LED
light on the AWR6032U receiver will be turned on. The corresponding channel 1 AF LED light or channel 2 AF
LED light will be on whenever the AWX6030 receives any sound while the On/Off switch is set at the “ON”
position.
7.
Adjust the volume control knob on the AWR6032U receiver to have an optimal sound quality.
(II)
LAPEL (LAVALIERE) MICROPHONE SYSTEM
1. Set the antennas at an angle 45° from the floor and 90° away from each other to achieve the best RF
reception.
2. Connect the AWR6032U receiver DC input to an AC power source via the supplied AC/DC adaptor.
3. Connect the AWR6032U receiver audio output to the microphone input of a mixer via the supplied audio cable
or any other appropriate cable. (Note: There are two outputs: one unbalanced output and one balanced
output.)
4.
Place one 9V battery into the battery housing of the AWX6030M transmitter with the battery polarity oriented
as indicated. Connect the supplied lapel (lavaliere) microphone to the AWX6030M transmitter.
5.
Turn on the power of the AWR6032U receiver. The Power On LED light will be turned on.
6.
On the
AWX6030M, the On/Off switch has three positions: “ON”, “STDBY” and “OFF”. When the On/Off
switch is turned to the “STDBY” or directly to the “ON” position, the low battery LED indicator will blink once
and then stay off. If the low battery LED indicator stays on, the 9V battery needs to be replaced. When the
On/Off switch is set to the “STDBY” or “ON” position, the corresponding channel 1 RF LED light or channel 2
RF LED light on the AWR6032U receiver will be turned on. The corresponding channel 1 AF LED light or
channel 2 AF LED light will be on whenever the AWX6030M transmitter receives any sound while the On/Off
switch is set at the “ON” position. The audio level adjustment knob is preset at midpoint. If you need to
increase the audio level, use a screwdriver to turn the audio level adjustment knob clockwise. Turn the audio
level adjustment knob counter-clockwise to reduce the audio level.
7.
Adjust the volume control knob on the AWR6032U receiver to have an optimal sound quality.
(III)
HEADSET MICROPHONE SYSTEM
1. Set the antennas at an angle 45° from the floor and 90° away from each other to achieve the best RF
reception.
2. Connect the AWR6032U receiver DC input to an AC power source via the supplied AC/DC adapter.
3. Connect the AWR6032U receiver audio output to the microphone input of a mixer via the supplied audio cable
or any other appropriate cable. (Note: There are two outputs: one unbalanced output and one balanced
output.)
4.
Place one 9V battery into the battery housing of the AWX6030H transmitter with the battery polarity oriented
as indicated. Connect the supplied headset microphone to the AWX6030H transmitter.
5.
Turn on the power of the AWR6032U receiver. The Power On LED light will be turned on.
6.
On the AWX6030H, the On/Off switch has three positions: “ON”, “STDBY” and “OFF”. When the On/Off
switch is turned to the “STDBY” or directly to the “ON” position, the low battery LED indicator will blink once
and then stay off. If the low battery LED indicator stays on, the 9V battery needs to be replaced. When the
On/Off switch is set to the “STDBY” or “ON” position, the corresponding channel 1 RF LED light or channel 2
RF LED light on the AWR6032U receiver will be turned on. The corresponding channel 1 AF LED light or
channel 2 AF LED light will be on whenever the AWX6030H transmitter receives any sound while the On/Off
switch is set at the “ON” position. The audio level adjustment knob is preset at midpoint. If you need to
