Audio2000's AMX7312, Owner'S Manual

Page: 4 / 6

1
3
2
6
8
7
1
5
2
3
4
9. [PEAK] LED Indicator --- This PEAK LED indicator will keep blinking when the input signal
level is higher than a predetermined threshold. When the PEAK LED indicator is blinking,
adjust the gain control knob (refer to numeral 4) to a lower gain level until the PEAK LED
indicator stops blinking to maintain the sound quality.
10. [LEVEL] Control Knob --- This knob is used to raise or lower the audio volume of the signal
from this channel.
1. Stereo Signal Level Meter --- This is a stereo signal
level meter configured with three green LED
lights at the bottom, one yellow LED light at the
middle, and one red LED light at the top on both
the left channel side and the right channel side.
When the red LED light is turned on frequently,
the [MAIN OUT] output signal level may need
to be lowered by adjusting the [STEREO] level
fader (refer to numeral 6). The red POWER LED
indicator lights are placed below the green level
meter LED lights.
2. [DELAY] Control Knob --- This control knob is used
to adjust the depth of the reverberation.
3. [REPEAT] Control Knob --- This control knob is used
to adjust the repetition times of the reverberation.
4. [FX LEVEL] Control Knob --- This effects return level
control knob is used to adjust the volume of the
reverberation effect.
5. [PHONES Level Control Knob --- This control knob
is used to adjust the earphone volume.
]
6. [STEREO] Level Fader --- This level fader is used to adjust the [MAIN OUT] output (refer to
numeral 1 in Section MAIN TERMINALS) signal volume.
7. [SEND] Level Control Knob --- This control knob is used to adjust the signal level from the
[SEND] output jack (refer to numeral 2 in Section MAIN TERMINALS).
8. [RETURN] Level Control Knob --- This control knob is used to adjust the signal level to the
[RETURN] input jack (refer to numeral 2 in Section MAIN TERMINALS).
5 6
1. [MAIN OUT] Stereo Output Jacks --- These are stereo main
output 1/4” TS jacks. These jacks are to be connected to
power amplifiers or active speakers.
2. [SEND & RETURN] Jacks --- Both the [SEND] and the [RETURN]
jacks are 1/4” TS jacks. The [SEND] output can be utilized
alone as a monitoring signal to a power amplifier or an active
speaker. The [RETURN] input jack can be utilized alone as
an input jack connecting to an external sound source.
External line devices (such as gating, compressing, equalizing,
and /or reverb effects) can be inserted into the signal path
between the [SEND] output jack and the [RETURN] input
jack to provide the desired sound effects.
3. [PHONES] Stereo Output Jack --- This is a 1/4” TRS jack for
the stereo monitoring earphones.
1
2
1. [DC IN] Power Supply Socket --- A supplied AC/DC power supply cord is to be connected
to this [DC IN] power supply socket, supplying DC+15V, DC-15V, DC+48V, and ground.
2. [POWER] Switch --- This is an ON/OFF power switch.
A B C D E
1
2
3 4
5
6
7
1. USB interface and MP3 display --- The volume and sound
quality of the audio signal from the USB interface are
controlled by the control knobs of the [5/6 USB] channel.
2. [+48V PHANTOM] Button/LED --- When one or more
condenser microphones are connected to the XLR [MIC]
input jacks (refer to numeral 1 in the CHANNEL INPUT
section), press this [+48V PHANTOM] button to turn on
the 48V phantom power to the condenser microphones
via the XLR [MIC] input jacks. When the 48V phantom
power is turned on, the phantom power LED light will be
turned on.
3. [5/6][USB] Selection Button --- Press down this button to select the stereo channel [5/6].
When this button is depressed, press this button again to raise the button to select the
USB input.
4. [3/4] Stereo Input Jacks --- These are the ¼” TS input jacks for channel 3 and channel 4.
Channel 3 is utilized as the left channel while channel 4 is utilized as the right channel
in the stereo mode. If only one 1/4” TS plug is connected to channel 3 and the channel 4
input jack is not connected, the mono audio signal to channel 3 will be routed to channel 4
simultaneously, such that both channel 3 and channel 4 carry the same mono audio signal.
5. [5/6] Stereo Input Jacks --- These are the ¼” TS input jacks for channel 5 and channel 6.
Channel 5 is utilized as the left channel while channel 6 is utilized as the right channel in
the stereo mode. If only one 1/4” TS plug is connected to channel 5 and the channel 6
input jack is not connected, the mono audio signal to channel 5 will be routed to channel 6
simultaneously, such that both channel 5 and channel 6 carry the same mono audio signal.
6. [TAPE/CD IN] Stereo Input Jacks --- These are the Tape/CD stereo RCA input jacks. The
volume and sound quality of the audio signal from these RCA input jacks are controlled
by the control knobs of the [5/6 USB] channel.
7. [REC OUT] Stereo Record Out Jacks --- These are the stereo RCA record-out jacks. The
audio signal to the stereo RCA record-out can be assigned from any input channel. The
level of the stereo RCA record-out signal is controlled by the stereo level fader (refer to
numeral 6 in the MAIN CONTROL section on page 6).
A. USB Insert
B. POWER LED Indicator
C. “ ”PLAY/PAUSE Button ---
Press this button to start playing the music from the USB
device. Press this button again to have the music paused. When the music is paused,
press this button will continue the music from where it was paused.
D. “ ”PREV Button --- Press this button to skip the current track and jump back to the
previous track.
E. “ ”NEXT Button --- Press this button to skip the current track and jump to the next track.