background image

Pro Series 5

 Installation and Operation 

5

Figure D — UniPak

® 

Transmitter 

UniPak

®

 Transmitter Battery Installation

1.  Open the transmitter door by first pulling the catch down and then  
 

sliding the door upward (Fig. D). 

2.  Observe correct polarity as marked and carefully insert two fresh  
 

1.5V AA alkaline batteries (Fig. D).

3.  Slide the door closed, making certain it clicks securely in  place.

UniPak

®

 Transmitter Battery Condition Indicator

After the battery is installed, press and hold the Power/Mute button until 
the indicator LED turns green (Fig.E). (It will turn red first; keep holding 
until it turns green). If the indicator LED does not light up when the 
Power/Mute button is pressed, the batteries are installed incorrectly or 
they are dead. The LED will flash to indicate low-battery condition.

UniPak

®

 Transmitter Mute Function

With the transmitter on, a slight touch of the Power/Mute button will 
toggle between muted and unmuted operation. Red LED indicates 
muted operation. Green LED indicates unmuted operation.

UniPak

®

 Transmitter Input Connection

Connect an audio input device (microphone or guitar cable) to the 
audio input connector on the top of the transmitter. A number of 
Audio-Technica professional microphones and cables are available 
separately, pre-terminated with a UniPak

®

 input connector (see www.

audio-technica.com.) 

UniPak

®

 Transmitter Antenna

The UniPak

®

 transmitter includes a permanently-attached flexible 

antenna. For best results, allow the antenna to hang freely and 
full length from the transmitter. If the received signal is marginal, 
experiment with different transmitter positions on your body or 
instrument; or try repositioning the receiver. 

Do not attempt to 

remove, replace or change the length of the transmitting antenna.

Figure E — UniPak

® 

Transmitter

Antenna

Input 

Connector

Indicator LED

(Power/Mute/Battery)

Power/Mute Button

Channel Selector 

Switch

Transmitter Door 

(Open Positon)

Screwdriver

RF Power 

Select Switch

Instrument Trim 

Control (Volume) 

Microphone Trim 

Control (Volume)

Transmitter 

Door Catch

Transmitter 

Door

Summary of Contents for Pro Series 5









Reviews: