ES935SH6
0.48"
12.3 mm
0.33"
8.4 mm
7.77"
197.3 mm
7.28"
185.0 mm
0.74"
18.9 mm
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com
0001-0124-01
Specifications
In the interest of standards development, A.T.U.S. offers full
details on its test methods to other industry
professionals on request.
1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
5. Using a 1.5 mm (
1
/
16
") drill bit, drill three pilot holes for the mounting
screws. (If mounting below the table surface, be certain
NOT
to drill
pilot holes through the table.)
6. Place the AT8474 mount over the hole and partially tighten the
three screws. Then place the microphone in the AT8474 so that the
microphone’s power module (base) extends through the AT8474 mount
into the hole. Tighten all three screws evenly. For maximum security,
the screws should be tight enough to ensure that the microphone is
held securely in place and cannot be removed without loosening
the screws.
7. If mounting the AT8474 mount below the surface of the table, slide
the rubber trim ring over the microphone (above the table surface) and
seat it between the microphone and the sides of the hole for a
finished appearance. (If mounting the AT8474 above the surface of the
table, you may also choose to use the trim ring beneath the surface of
the table, for added attenuation of noise, shock and vibration.)
8. After installing the microphone, assure maximum shock mount
effectiveness by providing some slack in the connecting cable. The
cable can be secured to the table with a standard wire clip or cable tie
(not included).
Architect’s and Engineer’s Specifications
The microphone shall be a fixed-charge condenser designed for
permanent installation or portable applications. It shall have a
hypercardioid polar pattern with a uniform 100° angle of acceptance
and a frequency response of 80 Hz to 20,000 Hz. It shall be capable of
accepting optional interchangeable elements for additional polar patterns.
The microphone shall operate from an external 11V to 52V DC phantom
power source. It shall be capable of handling sound input levels up to
138 dB with a dynamic range of 109 dB. Nominal open-circuit output
voltage shall be 10.0 mV at 1 V, 1 Pascal. Output shall be low impedance
balanced (250 ohms). It shall offer outstanding rejection of radio frequency
interference (RFI).
The microphone shall incorporate a self-contained power module with
an XLRM-type connector at the base for direct connection to a mating
XLRF-type panel jack or cable connector. It shall include a recessed
switch to permit choice of flat response or low-frequency roll-off. The
microphone shall incorporate an illuminating mute switch in the power
module. The mute switch shall illuminate when the microphone is on. The
mute switch shall be quiet in operation with no mechanical clicks or pops
and shall always return to the off position (after momentarily turning on to
verify microphone connection) when phantom power is restored.
A universal isolation-type shock mount suitable for above or below surface
installation shall be supplied for mounting the microphone in a solid surface.
It shall be possible to firmly secure the microphone in the mount. The mount
shall include appropriate hardware for installation. For alternative mounting
and portable applications, the microphone shall be supplied with a stand
clamp to permit attaching the microphone directly to a standard
5
/
8
"-27 or
3
/
8
"-16 thread. A two-stage foam windscreen shall also be included.
The microphone shall be a small-diameter gooseneck design, with an
overall length of 197.3 mm (7.77") and a head diameter of 8.4 mm (0.33").
Weight shall be 104 grams (3.7 oz). Finish shall be low- reflectance black.
The Audio-Technica ES935SH6 is specified.
Fixed-charge back plate, permanently
polarized condenser
Hypercardioid
80-20,000 Hz
80 Hz, 18 dB/octave
–40 dB (10.0 mV) re 1V at 1 Pa
250 ohms
138 dB SPL, 1 kHz at 1% T.H.D.
109 dB, 1 kHz at Max SPL
65 dB, 1 kHz at 1 Pa
11-52V DC, 4 mA typical
Flat, roll-off; mute/on
104 g (3.7 oz)
197.3 mm (7.77") long,
8.4 mm (0.33") head diameter,
18.9 mm (0.74") base diameter
Integral 3-pin XLRM-type
ESE-O omnidirectional (360°)
ESE-C cardioid (120°)
ESE-ML MicroLine
®
(90°)
M26
AT8474 universal isolation mount;
AT8473 quick-mount stand adapter;
5
/
8
"-
27 to
3
/
8
"-16 threaded adapter; AT8109
two-stage foam windscreen
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio
1
Phantom power requirements
Switches
Weight
Dimensions
Output connector
Optional interchangeable elements
Audio-Technica case style
Accessories furnished
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
12" or more on axis
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50
200
10k
5k
1k
500
2k
20k
Roll-off
frequency response: 80–20,000 Hz
polar pattern
269