[
ES935/C Specifications
†
]
Form No. 0309-2110-01-B/W P51271-01 © 2002 Audio-Technica U.S., Inc. Printed in U.S.A.
Element
Fixed-charge back
plate permanently
polarized condenser
Polar Pattern
Cardioid
Frequency Response
30-20,000 Hz
Low-frequency Roll-off
80 Hz, 12 dB/octave
Open Circuit Sensitivity
– 40 dB (10.0 mV)
re 1V at 1 Pa
*
Impedance
250 ohms
Maximum Input Sound
138 dB SPL, 1 kHz at
Level
1% T.H.D.
Dynamic Range
109 dB, 1 kHz at
(Typical)
Max SPL
Signal-to-noise Ratio
1
65 dB, 1 kHz at 1 Pa
*
Switch
Flat response,
low-roll-off
(recessed)
Phantom Power
11-52V DC, 4 mA
Requirements
typical
Weight
3.2 oz (92 grams)
Dimensions
7.52" (191.0 mm)
long,
0.33" (8.4 mm)
head diameter,
0.74" (18.9 mm)
base diameter
Output Connector
Integral 3-pin
XLRM-type
Accessories Furnished
AT8109 snap-on
foam windscreen;
AT8651thread-
mount adapter;
AT8658 shock
mount
Optional
ESE-H hypercardioid
Interchangeable
(100°)
Elements
ESE-ML MicroLine
®
(90°)
†
In the interest of standards development, A.T.U.S. offers full details
on its test methods to other industry professionals on request.
*
1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
Outside the U.S.A., please contact your local dealer for warranty details.
98.5 mm
3.88"
0.48"
12.3 mm
7.52"
191.0 mm
0.74"
18.9 mm
8.4 mm
0.33"
[
Dimensions
]
[
Polar Pattern
]
90
270
200 Hz
8 kHz
1 kHz
5 kHz
LEGEND
240
SCALE IS 5 DECIBELS PER DIVISION
180
210
120
150
300
330
60
30
0
One-Year Limited Warranty
Audio-Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of pur-
chase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such
defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or
superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other
proof of purchase date.
Prior approval from A.T.U.S. is required for return.
This warranty excludes defects due
to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty
is void in the event of unauthorized repair or modification.
For return approval and shipping information,
contact the Service Department, Audio-Technica U.S., Inc., 1221
Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential,
incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires
when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
[
Visit our Web site at www.audio-technica.com
]
[
Shock Mount Installation
]
B
C
3 x 120˚
FRONT
A
1. Locate the center of the mounting location and mark it.
Allow enough clearance to
accommodate the shock mount's flange on the desired surface and make certain there are no
physical obstructions below the desired location.
2. Using a 2
1
/
4
" (57 mm) hole saw, drill the large through-hole for the shock mount.
3. Set the shock mount into the hole and mark the location of the three mounting screw
holes.
Make certain to "center" the mount in the large hole before marking the three small
mounting screw locations.
4. Using a
1
/
16
" (1.5 mm) drill bit, drill three pilot holes for the mounting screws.
5. After installing the microphone, assure maximum shock mount effectiveness by providing
some slack in the connecting cable.
AT8658
Mounting Dimensions
A.
1
/
16
" (1.5 mm)
pilot holes 3 places on
2
1
/
2
" (64 mm) circle.
B.
2
1
/
4
" (57 mm)
thru-hole for mount
clearance.
C.
Outside edge of
flange, 3.07" (78 mm)
diameter.
Drawing not actual size.
Audio-Technica U.S., Inc.
1221 Commerce Drive, Stow, Ohio 44224
[
Frequency Response
]
20k
200
Roll-off
12" or more on axis (flat)
LEGEND
50
100
2k
Frequency in Hertz
500
1k
5k
10k
Response in dB
10 dB
