background image

5

Warnings

To prevent fire or shock hazard, do not 

expose your Reference Phono 3  

to rain or moisture.

Do not place objects containing 

water on top of this unit.

This unit contains voltages which can cause 

serious injury or death. Do not operate 

with covers removed. Refer servicing 

to your authorized Audio Research 

dealer or other qualified personnel.

The detachable power cord on your 

Reference Phono 3 is equipped with a heavy 

gauge, 3-conductor (where applicable) 

cable and a standard three-prong 

grounding plug.  For absolute protection, 

do not defeat the ground power plug. 

This provides power line grounding of 

the Reference Phono 3 chassis to provide 

absolute protection from electrical shock.

The appliance coupler (a.c. power connector) 

at the rear of this unit must be accessible 

for emergency power disconnect.

The power button on the front of this 

unit, when off, does 

not

 disconnect 

all power from this unit. This unit 

is in sleep mode when not on.

For continued protection against fire hazard, 

replace the fuse only with the same type 

and rating as specified at the fuse holder 

(see page 19 for fuse information).

This unit is RoHS compliant.

The Reference Phono 3 has automatic 

muting to help protect system components 

in the event of low line voltage. When 

sensing low line voltage, the preamp 

displays ‘Low Line’ and automatically goes 

into ‘Mute’. This condition will persist until 

the line voltage returns to a safe operating 

level; please note the unit will remain 

in ‘Mute’ even after ‘Low Line’ no longer 

appears.

Note that automatic muting is only 

designed to protect against power line 

interruptions or severe voltage drop. It 

will not mute in the event of subsonic 

transmissions from a faulty input source, 

amplifier failure or speaker malfunction. 

A note about packaging... 

Save all packaging in a dry place away 

from fire hazard. Your Reference Phono 

3 preamplifier is a precision electronic 

instrument and should be properly 

cartoned any time shipment is made. You 

may not have occasion to return your unit 

to the factory for service, but if that should 

prove necessary, or other occasion requiring 

shipment occurs, the original packaging 

will protect your Reference Phono 3 

from unnecessary damage or delay.

Summary of Contents for Reference Phono 3























Reviews: