background image

16

Warranty

Audio Research Corporation products are 

covered by a 3-Year Limited Warranty 

or a 90-Day Limited Warranty (vacuum 

tubes). This Limited Warranty initiates 

from the date of purchase, and is 

limited to the original purchaser, 

or in the case of demonstration 

equipment, limited to the balance 

of warranty remaining after original 

shipment to the retailer or importer.

In the United States, the specific terms, 

conditions and remedies for fulfillment 

of this Limited Warranty are listed on 

the warranty card accompanying the 

product in its shipping carton. The 

warranty terms are also available on the 

internet at www.audioresearch.com/

en-us/company/warranty-statement. 

Outside the United States, the authorized 

importing retailer or distributor has 

accepted the responsibility for warranty of 

Audio Research products sold by them.

The specific terms and remedies for 

fulfillment of the Limited Warranty may 

vary from country to country. Warranty 

service should normally be obtained from 

the importing retailer or distributor from 

whom the product was purchased.

In the unlikely event that technical service 

beyond the ability of the importer is 

required, Audio Research will fulfill the 

terms and conditions of the Limited 

Warranty. Such product must be 

returned at the purchaser’s expense to 

the Audio Research factory, along with a 

photocopy of the dated purchase receipt 

for the product, a written description 

of the problem(s) encountered, and 

any information necessary for return 

shipment. The cost of return shipment 

is the responsibility of the purchaser.

Summary of Contents for Reference 250 SE



















Reviews: