manualshive.com logo in svg

Audio enhancement TLD100, Operating Instructions Manual

Share
Download
Audio enhancement TLD100 Operating Instructions Manual Download Page 8

8

Major operating controls and their functions (IR-Satellite or Sensor)

Front

Back

①

 

Infrared sensor cover

 

To receive only the infrared by the inner sensor, the 
visible light is filtered out by this infrared sensor cover.

②

 

Operation indicator [OPERATE]  
(Green/Yellow/Red)

 

This LED lights green when the power is on and this 
unit is receivable under normal conditions.

 

This LED lights as follows to indicate other states:

 

F2 signal output provided: red light

 

Page mute signal received: yellow light

 

See page 16 for further information on operation.

③

 

Reception indicator [ / ]

 

This LED lights green when this unit is receiving sig-
nals from each microphone under normal conditions. 
This LED lights as follows to indicate other states:

 

F1 or F2 signal output provided: red light

 

Page mute signal received: yellow light

 

Feedback blocker in operation: yellow light

 

See page 16 for further information on operation.

④

 

LINE IN connector [LINE IN L/R]

 

This connector is used to provide an audio input from 
external sources such as a projector or CD. This is a 
stereo, line level input, and is internally mixed to a 
monaural signal.

 

A stereo mini plug (ø3.5 mm) is used.

⑤

 

Conversion box connector  
[TO CONVERSION BOX]

 

This connector is used to connect the cable to the 
supplied conversion box.

 

A standard CAT5 or CAT5e cable is used to connect 
to the conversion box.

CAUTION:

• 

DO NOT connect this device to any type of Ethernet 
(LAN) system.

⑥

 

Control (Auxillary) terminals

 

An 11-pin Euro block is used.

 

The following terminals are equipped.

 

F1 CNT: provides F1 signal* output controlled by 
MTD-09.

 

F2 CNT: provides F2 signal* output controlled by 
MTD-09.

 

* 

These are available when MTD-09 is used. 
Settings of F1 and F2 are performed with 
MTD-09.

 

F2 ACK: used to activate F2 ACK LED signal.

 

PAGE MUTE: provides signal inputs externally 
when the paging function is used.

 

RS-232C: is used to control this unit via communica-
tion from an external device.

⑦

 

Safety strap

 

This strap is attached to the ceiling mount bracket and 
prevents the sensor/receiver from dropping.

⑧

 

Extension sensor input connector  
[EXT SENSOR]

 

This connector is used for sensor extension. A single 
additional sensor (EDS-07) can be connected 
directly to this connector. A total of 4 sensors can be 
connected to this terminal with the additional coupler 
(AE-DCF).

④ ⑤

⑥

⑨

③

②

①

⑧

 

⑦

SG

RS-232C

RxD

TxD

GND

GND

F2 ACK

F2 COM

F2 CNT

F1 COM

F1 CNT

PAGE MUTE

2

1

Summary of Contents for TLD100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands