Audio Authority SF-16M, Installation Manual

Page: 26 / 36

26
BUS
IN
BUS
OUT
ASSIGN
CHANNEL
STEREO
MONO 1
MONO 2
MIX
OVER-
RIDE
BUS
FLEXPORT
761-391
ON
ON
MOMENTARY
TERM. ON
OFF
OFF
TOGL.
OFF
SWITCH
GAIN
MIN
MAX
BUS
IN
BUS
OUT
ASSIGN
CHANNEL
DUAL M
MONO 1
MONO 2
INPUT
MIX
OVER-
RIDE
BUS
PWR
FLEXPORT
761-392
MIC
ON
ON
MOMENTARY
TERM. ON
PHANT. OFF
LINE
OFF
OFF
TOGL.
OFF
ON
SWITCH
GAIN
MIN
MAX
FPM Rear Panel Connections and Settings
FlexPort RJ-45 Pinout
Not an Ethernet Port! It is recommended that all FlexPort bus Cat 5 wiring be config-
ured using the EIA-568B standard pinout. Audio Authority cannot garantee correct op-
eration using any other wiring configuration. Figure A-3 below shows both EIA-568B
and FlexPort RJ-45 pinouts.
FPM-B and FPM-X
A
FlexPort Bus In - Connects via Cat 5 to the FlexPort “Bus Out” of another FPM
in daisy chain scenarios
B
FlexPort Bus Out - Connects via Cat 5 to a SF-16M “FlexPort In” or in daisy
chain configurations to the “Bus In” of an additional FPM ( See
D
for audio
settings when daisy chaining )
C
Input Gain
- Increase or decrease input signal level prior to being sent to the
SF-16M
D
Assign Channel - The input source can be assigned as: Dual Mono (input is
assigned to both FlexPort channels), Mono 1 (FlexPort bus channel 1) or Mono 2
(channel 2)
E
Input Mic/Line
- Sets input gain as mic or line level
Mix On/Off - Allows two daisy chained FlexPort modules to mix together
upon override
Override On/Off - Enables or Disables override button on the front panel
Momentary/Toggle - Sets the override button to respond as a momentary or
toggle switch
Bus Termination On/Off - Turn on if the FPM is the last module in a daisy
chain configuration
Phantom Power On/Off - Turn on for phantom powered microphones
FPM-D and FPM-U
G
FlexPort Bus In
- Connects via Cat 5 to the FlexPort “Bus Out” of another FPM
in daisy chain scenarios
F
FlexPort Bus Out - Connects via Cat 5 to a SF-16M “FlexPort In” or in daisy
chain configurations to the “Bus In” of an additional FPM ( See
I
for audio
A
B
C
D
E
G
F
I
J
FPM-B and FPM-X
FPM-D and FPM-U
FlexPort Pinout:
(EIA-568B)
Pin 1: RS-485A
Pin 2: RS-485B
Pin 3: Audio Left +
Pin 4: Audio Right +
Pin 5: Audio Right –
Pin 6: Audio Left –
Pin 7: 18V
Pin 8: Ground
Figure A-1.
Figure A-2.
Figure A-3.
1 2 3 4 5 6 7 8
W-O O W-GR BL W-BL GR W-BR BR
Pair 2 Pair 4 Pair 1
Pair 3
T568B Pair Assignments
Modular Jack (RJ-45)
1 2 3 4 5 6 7 8
W-O O W-GR BL W-BL GR W-BR BR
Pair 2 Pair 4 Pair 1
Pair 3
T568B Pair Assignments
Modular Jack (RJ-45)
settings when daisy chaining )
H
Input Gain - Used to increase or decrease input
signal level prior to being sent to the SF-16M
I
Assign Channel Switch - The input source can be
assigned as: Stereo (default), Mono 1 (FlexPort bus
channel 1) or Mono 2 (channel 2)
J
Mix On/Off - Allows two daisy chained FlexPort
modules to mix together upon override
Override On/Off - Enables or Disables override
button on the front panel
Momentary/Toggle - Sets the override button to
respond as a momentary or toggle switch
Bus Termination On/Off - Turn on if the FPM is the
last module in a daisy chain configuration