ATX ivis Installation And Operation Manual Download Page 13

SERVICE & SUPPORT

5.  Service & Support

5.1.  Contact ATX Networks

Please contact ATX Technical Support for assistance with any ATX products. Please contact ATX Customer Service to obtain 

a valid RMA number for any ATX products that require service and are in or out-of-warranty before returning a failed module 

to the factory.

DIGITAL VIDEO TECHNICAL SUPPORT

Tel: 

(905) 428-6068

Toll Free: 

(800) 565-7488 (USA & Canada only) 

► Press 

*3 for 

Technical Support

  ►

Then press 1 for

 Digital Video Products (DVIS, DigiVu, UCrypt, VersAtivePro, VMS, DigiStream)

Email:  

[email protected]

CUSTOMER SERVICE

ATX Networks

1-501 Clements Road West

Ajax, ON L1S 7H4 Canada

Tel:  

(905) 428-6068

Toll Free: 

(800) 565-7488 (USA & Canada only) 

 

► Press *1 for 

Customer Service

Fax:  

(905) 427-1964

Toll Free Fax:  (866) 427-1964 (USA & Canada only)

Web: 

 

www.atxnetworks.com

Email:  

 

[email protected]

5.2.  Warranty Information

All of ATX Networks’ products have a 1-year warranty that covers manufacturer’s defects or failures. 

5.3. Safety

IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: 

Care should be taken so that objects do not fall and liquids are not spilled into the enclosure 

through openings.

POWER SOURCES:

 The device should be connected to a power supply only of the type described in the operating instructions 

or as marked on the device.

GROUNDING OR POLARIZATION: 

Precautions should be taken so that the grounding or polarization means of the device 

is not defeated.

POWER CORD PROTECTION: 

Power supply cords should be routed so that they are not likely to be pinched by items 

placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where 

they exit from the device.

SERVICING: 

The user should not attempt to service the device beyond that described in the operating instructions. All other 

servicing should be referred to qualified service personnel.

FUSING: 

If your device is equipped with a fused receptacle, replace only with the same type fuse. Refer to replacement text 

on the unit for correct fuse type.

          MMDU Solutions

®

 – IVIS Indoor Video Insertion System - Instalation & Operation Manual 

5-1

 

CHAPTER 5:  SERVICE & SUPPORT

CHAPTER 4:  RF LEVEL ADJUSTMENT

Summary of Contents for ivis















Reviews: