x
IPDHCP
Regulates how the iPBridge acquires its IP address.
When disabled, the iPBridge uses the IP address
specified by the
enabled, the iPBridge gets its IP address from a DHCP
server.
Default: enabled
set IPDHCP [dp1 | mp1 | all] [enabled | disabled]
SaveConfiguration Restart command required
get IPDHCP [dp1 | mp1 | all]
IPGateway
Controls the current default gateways used by any
Ethernet ports on the iPBridge. If
is enabled,
the
get
command reports the current IP gateway
assigned by the network DHCP server.
Default: 0.0.0.0
set IPGateway [dp1 | mp1 | all] [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get IPGateway [dp1 | mp1 | all]
IPSubnetMask
Controls the current subnet masks used by any Ethernet
ports on the iPBridge. If
is enabled, the get
command reports the current IP subnet mask assigned by
the network DHCP server.
Default: 255.255.0.0
set IPSubnetMask [dp1 | mp1 | all] [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get IPSubnetMask [dp1 | mp1 | all]
iSCSIAlias
Assigns a human-readable name to the iPBridge. Aliases
may be 1 to 64 characters in length and may contain
spaces if enclosed in quotes.
Default: “ “
set iSCSIAlias [Alias]
get iSCSIAlias
iSCSIChap
Regulates whether CHAP (Challenge-Handshake
Authentication Protocol) is to be used for the iSCSI
protocol. If CHAP is enabled, the target requires the
initiator to negotiate CHAP authentication using the
CHAP secrets. An initiator may reject this negotiation. If
discovery
is specified, the setting applies to CHAP
during discovery sessions.
Default: disabled
set iSCSICHAP [default | Target Name | discovery]
[enabled | disabled]
get iSCSICHAP [default | Target Name | discovery]
iSCSIChapSecret
Specifies the incoming and outgoing passwords for iSCSI
CHAP sessions. Secrets are case sensitive, 12 to 32
characters, and cannot contain spaces.
In
and
out
secrets must be different for each name. If
discovery
is
specified, the setting applies to CHAP during discovery
sessions. An
in
secret authenticates the server to the
iPBridge. The iPBridge can store up to 32
in
secrets,
each with a unique Account Name and secret pair. An
out
secret authenticates the iPBridge to the server. There is
only one
out
secret per target which cannot be deleted.
The
account name
for the out secret is
root
by default.
set iSCSICHAPSecret [default | target name | discovery]
[in [Account Name | all] | out [root] | delete [Account
Name | all]] <Secret>
get iSCSICHAPSecret [default | target name | discovery]
[in [Account Name | all] | out [root]]
iSCSIInitiators
Displays a list of previous and current successfully
logged-in iSCSI initiators, including successful initiators
recorded in the event log and any initiators manually
added since the last reboot. This list is cleared if the event
log is cleared.
iSCSIInitiators
iSCSIPortNumber
Specifies the port number which listens for iSCSI
connections. Port number must be between 1024 and
65535 with the exception of port 860.
Default: 3260
set iSCSIPortNumber [dp1 | all] [portnumber]
get iSCSIPortNumber [dp1 | all]
Summary of Contents for iPBridge 2600
Page 1: ...ATTO iPBridge 2600 Installation and Operation Manual...
Page 7: ...2 Exhibit 1 0 1 Possible storage configurations...
Page 9: ...4 Exhibit 1 1 1 Details of the LED indicators on the front and connector sides of the iPBridge...
Page 50: ...xix ATTO Technology Inc iPBridge Installation and Operation Manual...
