background image

Hardware Guide AG-811

4. System functions

4.1.

Schedule timers for control outputs

To  control   3   outputs,   device   has   3  separate  timetable   with   on/off   schedule.   Total   timer
schedule can implement up to 10 on/off sequence in 24h for each output.

4.2.

Astronomical timer for control outputs

Device has 2 table position to switch on/off the outputs according to sunrise or sunset. The
actual sunrise/sunset time is calculated from actual latitude and longitude and actual time.
Latitude and longitude has to be entered manually in configuration web page or can be
setted remotely.

4.3.

SMS alerts

There is option to send SMS alert to the dedicated mobile number when any one of digital
inputs is activated. For details see AG-811 Configuration Guide.

4.4.

Configuration of device

Configuration of AG-811 can be done by:

Internal website

For configuration by internal website connect the laptop by LAN cable to the device and in
browser   type   IP   address   of   device   192.168.10.50.   It   is   necessary   to   make   proper
configuration of LAN network in laptop.

SMS commands

Device   allow   to   make   configuration   by   SMS   command.   There   is   option   to   filter   allowed
mobile number to make configuration.

String from TCP/IP server 

By   the   command   from   server   it   is   possible   to   make   all   configuration.   But   initially   it   is
necessary to set server configuration in device by SMS or internal website..

File remotely loaded from server URL

The device can upload configuration file from remote URL. The configuration of URL initially
can be done by SMS or by internal website.

Configuration details are specified in separate document – AG-811 Configuration Guide.

4.5.

Power supply

The device is powered by external DC power supply. Minimum supply voltage  is 8V and
maximum 36V. Preferred 24V. Select the power supply requirement according to the below
table. The device had protection against high voltage and reverse polarity. High voltage will
blow inbuilt fuse. Reverse voltage will not damage device – the device will simply not work
on reverse voltage.

           

www.atreyo.in

  ARAD/AG-811/HG/2022/02 – preliminary

 Page |9

Summary of Contents for AG-811
















Reviews: