ATP Electronics Piper Archer Training Supplement Download

Page: 7 / 60

Aircraft Systems • 3

Flaps

The Archer is equipped with a manual flap system. The flaps are extended with

a lever located between the two pilot seats. Flap settings are 0°, 10°, 25°, and 40°,

and are spring-loaded to return to the 0 ° position.

ATP operations require flaps 25° for all landings except:

• Short and soft field, flaps 40°
• Precision approach, flaps 10°

Pitot Static

Pitot and static pressure are both received from a pitot head installed on the

bottom of the left wing. An alternate static source is located inside the cabin

under the left side of the instrument panel, for use in the event of static port

blockage. When using the alternate static source, the storm window and cabin

vents must be closed and the cabin heater and defroster must be on. This will

reduce the pressure differential between the cockpit and the atmosphere,

reducing pitot-static error. The pitot-static instruments are the airspeed

indicator, altimeter, and vertical speed indicator.

Both the pitot and static lines can be drained through separate drain valves

located on the left lower side of the fuselage interior.

Fuel System

The Archer, which uses 100 low lead avgas (blue), is equipped with two 25

gallon fuel tanks. One gallon is unusable in each tank. There is one engine-

driven and one electrically-driven fuel pump. The electric fuel pump is used for

all takeoffs and landings, and when switching tanks.

ATP uses the electric fuel pump for in-flight maneuvers, except
for steep turns.

The aircraft is equipped with a three-position fuel selector control. The positions

are “L”, “R”, and “OFF”.

The correct procedure for switching tanks in cruise flight is:

1. Electric fuel pump on

2.  Fuel selector from “L” to “R” or from “R” to “L”
3.  Check fuel pressure
4.  Electric fuel pump off
5.  Check fuel pressure

Summary of Contents for Piper Archer





























































Search results

Summary of Contents for Piper Archer

Reviews:

Related manuals for Piper Archer

Brands by name

Popular brands

ATP Electronics Piper Archer, Training Supplement

Search results

Summary of Contents for Piper Archer

Reviews:

Related manuals for Piper Archer

Brands by name

Popular brands