ATN BinoX 4K, Manual, Page: 4 / 13

6 7
NOTE
There is only one correct direction to
insert the microSD Card.
Do not force the microSD Card into the
port doing so may cause damage to both
the binocular and the card itself.
To remove the microSD Card from the
port, push the card slightly in using the
same thin object you did before. When the
card pops up a few millimeters, pull the card
out with your fingers or tweezers.
NOTE
ATN recommends a microSD Card should be a Class 10 (10 Mb/sec) or
faster and have capacity from 4 to 64 Gb that is an HC type SD card.
FIRMWARE UPDATE
Before operating your device, update the firmware to the latest version. All
firmware updates can be found on at https://www.atncorp.com/firmware.
To update the firmware you will need a microSD Card and fully charged in-
ternal battery.
To receive a notification concerning new firmware updates, please register
your device on our website. An email notification will be sent when a new firm-
ware update becomes available.
NOTE
In the event of a power failure during an update, the device may crash.
This will corrupt the system files and the device will need to be sent back
to the ATN factory for service.
Update the new firmware as follows:
1. Download the ***.bin file and copy
to your microSD Card — root direc-
tory.
2. Insert the card into the binocular.
3. Turn ON the binocular.
4. In the “Firmware Update” dialog box
select “Yes” to start the update.
5. When the update counter reaches
“100%” the device will automatical-
ly restart.
6. Once the device is powered up it will enter self configuration mode.
7. After completing it will automatically restart.
8. Motion Sensing platform will be configured when first turned on.
9. Once the Firmware update completes, please do a factory reset before
using the product.
NOTE
If the device does not restart within 30 seconds, press and hold the
power button for 15 seconds and the binocular will turn off.
PR E PA R I N G T H E D E V I C E
The following steps must be performed before using the device.
UNPACKING
1. Open the BinoX 4K box packaging.
2. Verify your box has the following: soft carrying case, neck strap, USB-C
charging cable, lens cover, and lens tissue.
3. Inspect the device for damage to optical surfaces, body, eyecups, opera-
tion buttons, etc.
4. Ensure that all optical surfaces are clean and ready for use.
NOTE
If any accessories are missing or broken contact ATN’s Customer Ser­
vice at 1.800.910.2862.
CHARGING THE DEVICE
The device is equipped with a USB (type C) port. You will find it under the
rubber cap on the right side of the device (caps are marked with appropriate
icon).
Use the included USB (type C) charging cable with your binocular. Plug the
cable into a USB wall charger that has an output of 2 amps (Wall Charger not
included).
NOTE
Using a wall charger with lower amperage will increase charge time on
your binocular.
1. Recommended charger is 2A USB charger.
2. Battery charging time (from 0 to 100%) is 6 hours with 2 A USB charger.
3. Battery run time is 15 hours on a single charge.
MICRO SD AND USB C PORTS
The device is equipped with a microSD
Card port and USB (type C) port. You can
find them under the rubber cap on the right
side of the device (we marked the cap with
appropriate icons).
To open the rubber port cover, gently lift
the rubber cover and move it out of the way.
NOTE
Make sure that the device is turned off
before inserting the formatted microSD
Card into its assigned port.
1. Always format a new microSD card be-
fore using.
2. Insert microSD card as shown.
3. Use a thin object (small coin, paper clip)
to lock the microSD card in place after in-
serting it into the slot.
4. Return the cover to its original position.
USB,type C
MicroSD