Atmel XMEGA B User Manual Download | Manualshive

Page: 228 / 415

background image

228

XMEGA B [DATASHEET]

8291B–AVR–01/2013

18.14 Register Description

–

USB Endpoint

Each of the 16 endpoint addresses have one input and one output endpoint. Each endpoint has eight bytes of
configuration/status data located in internal SRAM.

The address to the first configuration byte is (EPPTR[15:0] + 16 × endpoint address) for output endpoints and
(EPPTR[15:0] + 16 × endpoint a 8) for input endpoints.

Some bit locations have different functions, depending on endpoint configuration type or direction, and this is reflected by
using two different names for the bit locations.

18.14.1 STATUS – Status register

Note:

1.

For isochronous endpoints.



Bit 7 – STALL: STALL Flag

This flag is set when an IN or OUT transaction has been responded to with a STALL handshake. This flag is cleared by
writing a one to its bit location.



Bit 7 – CRC: CRC Error Flag

This flag is set for isochronous output endpoints when a CRC error has been detected in an incoming data packet. This
flag is cleared by writing a one to its bit location.



Bit 6 – UNF/OVF: Underflow/Overflow Flag

UNF: For input endpoints, the UNF flag is set when an input endpoint is not ready to send data to the host in response of
an IN token.

OVF: For output endpoints, the OVF flag is set when an output endpoint is not ready to accept data from the host
following an OUT token.



Bit 5 – TRNCOMPL0: Transaction Complete Flag

This flag is set when an IN or OUT transaction has completed successfully. This flag is cleared by writing a one to its bit
location.



Bit 4 – SETUP: SETUP Transaction Complete Flag

This flag is set when a SETUP, IN, or OUT transaction has completed successfully. This flag is cleared by writing a one
to its bit location.



Bit 4 – TRNCOMPL1: Transaction Complete Flag

This flag is set when a SETUP, IN, or OUT transaction has completed successfully. This flag is cleared by writing a one
to its bit location.



Bit 3 – BANK: Bank Select Flag

When ping-pong mode is enabled, this bit indicates which bank will be used for the next transaction. BANK is toggled
each time a transaction has completed successfully. This bit is not sed when ping-pong is disabled. This flag is cleared
by writing a one to its bit location.



Bit 2 – BUSNACK1: Data Buffer 1 Not Acknowledge Flag

When this flag is set, the USB module will discard incoming data to data buffer 1 in an OUT transaction, and will not
return any data from data buffer 1 in an IN transaction. For control, bulk, and interrupt endpoints, a NAK handshake is
returned. This flag is cleared by writing a one to its bit location.

Bit

7

6

5

4

3

2

1

0

STALL

UNF/ OVF

TRNCOMPL0

SETUP

BANK

BUSNACK1

BUSNACK0

TOGGLE

CRC

TRNCOMPL1

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

«
...
226
227
228
229
230
...
»

Summary of Contents for XMEGA B
































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XMEGA B

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Saitek Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: UE Pages: 4

Brand: Salda Pages: 16

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: IBM Pages: 20

Brand: DAV TECH Pages: 24

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 16

Brand: Dejero Pages: 24

Brand: WINDY NATION Pages: 16

Brand: Kaba Mauer Pages: 10

Saxun Mosquito Screen Lateral Door 2020

Brand: Gimenez Ganga Pages: 2

Brand: Keysight Technologies Pages: 78

Brand: Festo Pages: 87

Brand: CAME Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands