background image

 

 

Atmel AVR32918: UC3-A3 Xplained Hardware User’s Guide [APPLICATION NOTE] 

32159C

AVR

07/2012 

3

1. 

Related items 

Xplained is a series of small-sized and easy-to-use evaluation kits for 8- and 32-bit AVR microcontrollers. It consists of 
a series of low cost MCU boards for evaluation and demonstration of feature and capabilities of different MCU families. 

Atmel Studio is a free IDE for development of C/C++ and assembler code for Atmel microcontrollers. 

BatchISP (FLIP) is a command line tool for programming the flash and EEPROM memories of the AVR and is part of 
the FLIP installation. It can be used to communicate with the preprogrammed USB DFU boot loader. 

 

JTAGICE 3 is a mid-range development tool for Atmel 8- and 32-bit AVR microcontrollers with on-chip debugging for 
source level symbolic debugging, NanoTrace (if supported by the device) and device programming. 

 

AVR ONE! is a professional development tool for all Atmel 8- and 32-bit AVR devices with on-chip debug capability. It is 
used for source level symbolic debugging, program trace, and device programming. The AVR ONE! supports the 
complete development cycle and is the fastest debugging tool offered from Atmel. 

 

The Atmel® Software Framework (ASF) is a collection of embedded software for Atmel flash MCU. 

 

2. 

General information 

The Atmel UC3-A3 Xplained kit is intended to demonstrate the Atmel AT32UC3A3256 microcontroller. 

Figure 2-1

 shows 

the available feature on the board. 

Figure 2-1.  Overview of the UC3-A3 Xplained kit. 

 

Summary of Contents for AVR32918











Reviews: