Atmel AVR ATmega328P Manual Download | Manualshive

Page: 191 / 452

background image

191

8025I–AVR–02/09

ATmega48P/88P/168P/328P

Figure 17-5. Start Bit Sampling

When the clock recovery logic detects a high (idle) to low (start) transition on the RxDn line, the
start bit detection sequence is initiated. Let sample 1 denote the first zero-sample as shown in
the figure. The clock recovery logic then uses samples 8, 9, and 10 for Normal mode, and sam-
ples 4, 5, and 6 for Double Speed mode (indicated with sample numbers inside boxes on the
figure), to decide if a valid start bit is received. If two or more of these three samples have logical
high levels (the majority wins), the start bit is rejected as a noise spike and the Receiver starts
looking for the next high to low-transition. If however, a valid start bit is detected, the clock recov-
ery logic is synchronized and the data recovery can begin. The synchronization process is
repeated for each start bit.

17.8.2

Asynchronous Data Recovery

When the receiver clock is synchronized to the start bit, the data recovery can begin. The data
recovery unit uses a state machine that has 16 states for each bit in Normal mode and eight
states for each bit in Double Speed mode.

shows the sampling of the data bits and

the parity bit. Each of the samples is given a number that is equal to the state of the recovery
unit.

Figure 17-6. Sampling of Data and Parity Bit

The decision of the logic level of the received bit is taken by doing a majority voting of the logic
value to the three samples in the center of the received bit. The center samples are emphasized
on the figure by having the sample number inside boxes. The majority voting process is done as
follows: If two or all three samples have high levels, the received bit is registered to be a logic 1.
If two or all three samples have low levels, the received bit is registered to be a logic 0. This
majority voting process acts as a low pass filter for the incoming signal on the RxDn pin. The
recovery process is then repeated until a complete frame is received. Including the first stop bit.
Note that the Receiver only uses the first stop bit of a frame.

Figure 17-7 on page 192

shows the sampling of the stop bit and the earliest possible beginning

of the start bit of the next frame.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

1

2

START

IDLE

0

0

BIT 0

3

1

2

3

4

5

6

7

8

1

2

0

RxD

Sample

(U2X = 0)

Sample

(U2X = 1)

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

1

BIT n

1

2

3

4

5

6

7

8

1

RxD

Sample

(U2X = 0)

Sample

(U2X = 1)

«
...
189
190
191
192
193
...
»

Summary of Contents for AVR ATmega328P





































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AVR ATmega328P

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Brand: 3Com Pages: 8

Brand: Harmonic Pages: 56

Brand: IEI Technology Pages: 3

Brand: Alcad Pages: 6

Brand: ROE Pages: 41

Brand: Gate Pages: 8

Brand: Avolites Pages: 24

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

Brand: VCS Pages: 118

Brand: UNA AUTOMATION Pages: 20

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: Renesas Pages: 4

Brand: CyberResearch Pages: 59

Brand: ActiveEye Pages: 35

Pixel Processing Juggler

Brand: 7th Sense Pages: 148

Brand: CoolShirt Pages: 3

Brand: Extron electronics Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands