Atmel ATSAML22G16A-AUT Manual Download Page 82 | Manualshive

Page: 82 / 1231

background image

Figure 14-4. APB Memory Mapping

0x0000

0x00FC

0x0100

0x01FD

0x1000

0x1FFC

DSU operating

registers

Replicated

DSU operating

registers

DSU CoreSight

ROM

Empty

Internal address range
(cannot be accessed from debug tools when the device is
protected by the NVMCTRL security bit)

External address range
(can be accessed from debug tools with some restrictions)

Some features not activated by APB transactions are not available when the device is protected:

Table 14-1. Feature Availability Under Protection

Features

Availability when the device is protected

CPU Reset Extension

Yes

Clear CPU Reset Extension

No

Debugger Cold-Plugging

Yes

Debugger Hot-Plugging

No

Related Links

NVMCTRL – Non-Volatile Memory Controller

on page 515

on page 523

14.10. Device Identification

Device identification relies on the ARM CoreSight component identification scheme, which allows the chip
to be identified as an Atmel device implementing a DSU. The DSU contains identification registers to
differentiate the device.

14.10.1. CoreSight Identification

A system-level ARM CoreSight ROM table is present in the device to identify the vendor and the chip
identification method. Its address is provided in the MEM-AP BASE register inside the ARM Debug
Access Port. The CoreSight ROM implements a 64-bit conceptual ID composed as follows from the PID0
to PID7 CoreSight ROM Table registers:

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

82

«
...
80
81
82
83
84
...
»

Summary of Contents for ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ATSAML22G16A-AUT

Brand: 3Ware Pages: 2

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: Aurora Pages: 2

Brand: Altronix Pages: 8

Brand: nvent Pages: 6

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Freedom Bridge FB3

Brand: Identiv Pages: 2

Brand: Rheem Pages: 2

STM32F469 Series

Brand: ST Pages: 31

Brand: FAAC Pages: 25

Brand: Digi Pages: 19

Brand: DIG Pages: 16

Brand: Danfoss Pages: 118

Reference 20 Plus A/V System Controller

Brand: B&K Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands