AtlasIED HPA-DAC8 Owner'S Manual Download Page 11

– 11 –

HPA-DAC8

Owner’s Manual

AtlasIED.com

TELEPHONE: (800) 876-3333

[email protected]

1601 JACK MCKAY BLVD. 

ENNIS, TEXAS 75119 U.S.A.

Limited Warranty

All products manufactured by AtlasIED are warranted to the original dealer / installer, 
industrial or commercial purchaser to be free from defects in material and workmanship 
and to be in compliance with our published specifications, if any. This warranty shall 
extend from the date of purchase for a period of three years on all AtlasIED products, 
including SOUNDOLIER brand, and ATLAS SOUND brand products except as follows: one 
year on electronics and control systems; one year on replacement parts; and one year on 
Musician Series stands and related accessories. Additionally, fuses and lamps carry no 
warranty. AtlasIED will solely at its discretion, replace at no charge or repair free of charge 
defective parts or products when the product has been applied and used in accordance 
with our published operation and installation instructions. We will not be responsible for 
defects caused by improper storage, misuse (including failure to provide reasonable and 
necessary maintenance), accident, abnormal atmospheres, water immersion, lightning 
discharge, or malfunctions when products have been modified or operated in excess 
of rated power, altered, serviced or installed in other than a workman like manner. The 
original sales invoice should be retained as evidence of purchase under the terms of this 
warranty. All warranty returns must comply with our returns policy set forth below. When 
products returned to AtlasIED do not qualify for repair or replacement under our warranty, 
repairs may be performed at prevailing costs for material and labor unless there is included 
with the returned product(s) a written request for an estimate of repair costs before 
any nonwarranty work is performed. In the event of replacement or upon completion of 
repairs, return shipment will be made with the transportation charges collect.
EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF 
CONSEQUENTIAL DAMAGES FOR PERSONAL INJURY, ATLASIED SHALL NOT BE 
LIABLE IN TORT OR CONTRACT FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL 
LOSS OR DAMAGE ARISING OUT OF THE INSTALLATION, USE OR INABILITY TO USE 
THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES 
INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE.
AtlasIED does not assume, or does it authorize any other person to assume or extend on 
its behalf, any other warranty, obligation, or liability.  
This warranty gives you specific legal rights and you may have other rights which vary 
from state to state.

Summary of Contents for HPA-DAC8













Reviews: