Atlas AA50PHD Owner'S Manual Download Page 20

 AtlasSound.com 

– 20 – 

Owner’s Manual

AA50PHD

50W Mixer Amplifier

1601 Jack McKay Blvd. • Ennis, Texas 75119  U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

Limited Warranty

All products manufactured by Atlas Sound are warranted to the original dealer/installer, industrial or commercial purchaser to be free 
from defects in material and workmanship and to be in compliance with our published specifications, if any. This warranty shall extend 
from the date of purchase for a period of three years on all Atlas Sound products, including SOUNDOLIER brand, and ATLAS SOUND 
brand products except as follows: one year on electronics and control systems; one year on replacement parts; and one year on 
Musician Series stands and related accessories. Additionally, fuses and lamps carry no warranty. Atlas Sound will solely at its discretion, 
replace at no charge or repair free of charge defective parts or products when the product has been applied and used in accordance 
with our published operation and installation instructions. We will not be responsible for defects caused by improper storage, misuse 
(including failure to provide reasonable and necessary maintenance), accident, abnormal atmospheres, water immersion, lightning 
discharge, or malfunctions when products have been modified or operated in excess of rated power, altered, serviced or installed 
in other than a workman like manner. The original sales invoice should be retained as evidence of purchase under the terms of this 
warranty. All warranty returns must comply with our returns policy set forth below. When products returned to Atlas Sound do not 
qualify for repair or replacement under our warranty, repairs may be performed at prevailing costs for material and labor unless there is 
included with the returned product(s) a written request for an estimate of repair costs before any nonwarranty work is performed. In 
the event of replacement or upon completion of repairs, return shipment will be made with the transportation charges collect.

EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL DAMAGES FOR PERSONAL 
INJURY, ATLAS SOUND SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL 
LOSS OR DAMAGE ARISING OUT OF THE INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS 
IN LIEU OF ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 
A PARTICULAR PURPOSE.

Atlas Sound does not assume, or does it authorize any other person to assume or extend on its behalf, any other warranty, obligation, 
or liability. This warranty gives you specific legal rights and you may have other rights which vary from state to state.

Service

Should your AA50PHD require service, please contact the Atlas Sound warranty department at

1-877-689-8055, ext. 277 or support.atlassound.com to obtain an RA number.

Atlas Sound Tech Support can be reached at 1-800-876-3333 or support.atlassound.com.

Visit our website at www.AtlasSound.com to see other Atlas products.

©2014 Atlas Sound L.P. All rights reserved. Atlas Sound is a trademark of Atlas Sound L.P. 

All other trademarks are the property of their respective owners. ATS004884 RevA 9/14

Summary of Contents for AA50PHD





















Reviews: