Atlas Copco XAS 185 KDU T4F HOP Instruction Manual Download Page 54

Page: 54 / 62

- 54 -

Technical specifications

TORQUE VALUES

GENERAL TORQUE VALUES

The following tables list the recommended torques applied for general applications at

assembly of the compressor.

For hexagon screws and nuts with strength grade 8.8

For hexagon screws and nuts with strength grade 12.9

CRITICAL TORQUE VALUES

Thread size

Torque value, Nm (lbf.ft)

8(6)±25%

20(15)±25%

M10

40(30)±25%

M12

69(51)±25%

M14

109(80)±25%

M16

171(126)±25%

Thread size

Torque value, Nm (lbf.ft)

14(10)±25%

34(25)±25%

M10

68(50)±25%

M12

116(86)±25%

M14

185(136)±25%

M16

288(212)±25%

Assemblies

Torque value

Variance

Axles to frame:

ft.lbf

Wheel nuts

N/A

Bolts, axle(s)/frame

N/A

Compressor to frame:

Bolts, elements/gear casing

±10%

Bolts, elements/support

±10%

Bolts, support/buffer

N/A

Bolts, buffer/frame

N/A

Engine to frame:

Bolts, engine/support

±10%

Bolts, support/buffer

±10%

Bolts, buffer/frame

±10%

Lifting beams to0frame:

Bolts, lifting beams/yoke (M16)

N/A

Bolts, lifting beams/yoke (M12)

±10%

Bolts, lifting beams/A-Frames

N/A

Bolts, A-Frames/frame

N/A

Hose clamps:

Worm Type

4.3

3.2

±10%

Constant Torque Type

4.3

3.2

±10%

Heavy Duty Constant Torque Type

7.4

±10%

Secure the drain cock and tank cap of the fuel tank hand tight.

Summary of Contents for XAS 185 KDU T4F HOP































































Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Related manuals for XAS 185 KDU T4F HOP

Brands by name

Popular brands

Atlas Copco XAS 185 KDU T4F HOP, Instruction Manual

Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Related manuals for XAS 185 KDU T4F HOP

Brands by name

Popular brands