Atlas Copco ITB-A31-05-I06, Safety Information Manual

Page: 3 / 168

ITB-A31-05-I06 Safety Information
© Atlas Copco Industrial Technique AB - 9834 5879 00
3
Technical Data
Product Data
Motor voltage 35 V d.c.
Motor power 1080 W
Speed 2972 r/min
Torque range 1 - 5 Nm (0.7 - 3.6 ft lb)
Weight 1.5 kg (3.3 lb)
Battery Compatibility
Accessory Article nr.
Battery, 14V (2.5Ah) 4211 6130 02
Battery, 18V (2.5Ah) 4211 6030 85
Battery, 36V (2.5Ah) 4211 6030 86
Maximum Radio Output Power
Radio Technology
Frequency Range
(MHz)
Maximum Trans-
mit Power EIRP
(dBm)
Wi-Fi® 2402-2480 19.46
Wi-Fi® 5180-5320 20.37
Wi-Fi® 5500-5700 18.39
Bluetooth® wire-
less technology /
Bluetooth® Low
Energy 2402-2480 9.29
Wi-Fi® is a registered trademark of Wi-Fi Alliance®
The Bluetooth® word mark and logos are registered trade-
marks owned by Bluetooth SIG,Inc.
Wireless LAN Information
Regulatory Do-
main Band TxChannels
ETSI 2.4 GHz 1, 2, 3, 4, 5, 6, 7, 8,
9, 10, 11
U-NII-1 36, 40, 44, 48
U-NII-2 52, 56, 60, 64
U-NII-2e 100, 104, 108, 112,
116, 120, 124, 128,
132, 136, 140
FCC/IC
2.4 GHz 1, 2, 3, 4, 5, 6, 7, 8,
9, 10, 11
U-NII-1 36, 40, 44, 48
U-NII-2 52, 56, 60, 64
U-NII-2e 100, 104, 108, 112,
116, 132, 136, 140
U-NII-3 149, 153, 157, 161,
165
Charger Compatibility
Accessory Article nr.
Flex charger 4211 6083 84
EU SAR value
EU SAR Value: 0.55
Charger Temperatures
Charger operating tempera-
ture +5 to +40 °C
(+41 to +104 °F)
Ambient Temperature
Operating temperature, charge +5 to +40 °C
(+41 to +104 °F)
Operating temperature, discharge 0 to +40 °C
(+32 to +104 °F)
Storage temperature −20 to +40 °C
(−4 to +104 °F)
Cable Power Supply Unit Compatibility
Accessory Article nr.
Power Supply Unit 950 8432084004
Power Supply Unit 950 8432084006
Product Power Source
This product can be used with either a battery, or with an
electrical power cable in combination with a power supply
unit.
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rota-
tional direction after any event that can influence the tighten-
ing result. Examples of such events include but are not lim-
ited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures
or practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should: