Atlantic Ultraviolet Sanidyne 40-0634A Owner'S Manual Download Page 3

3

SAFETY INSTRUCTIONS

  To guard against injury, basic safety precautions should be observed, including the following:

1. 

Read and follow 

ALL

 safety instructions.

2.   

 

  Avoid exposure to direct or reflected germicidal ultraviolet rays. Germicidal 

ultraviolet rays are 

harmful 

to the eyes and skin.

3.  Intended for indoor use only.
4.  Do not alter design or construction.
5.  Do not use this sanitizer for other than its intended purpose, as described in this manual.
6.  Do not use this sanitizer in occupied areas. The supplied “

DANGER - DO NOT ENTER…

” sign(s) 

MUST

 be clearly 

displayed to warn against entering the area during the disinfection cycle without proper personal protection equipment.

7. 

Germicidal ultraviolet rays may break down plastic, rubber or other non-metallic materials, with 

inadequate resistance to ultraviolet. Shield all plastic, rubber or other non-metallic parts which may be exposed to direct or 

reflected germicidal ultraviolet rays.

8.  Do not remove any labels.
9. 

 

  Do not operate without proper electrical ground.

10. 

Do not operate the sanitizer if the power cord and/or plug are damaged, or if any other damage to the sanitizer is 

 

visible or suspected.

11. 

Utility power supplied to the sanitizer, 

MUST

 match power requirements listed on the sanitizer label.

12. 

 

  

Always disconnect power to the fixture before performing any service or maintenance

.

13. 

Read and follow all notices and warnings on the sanitizer.

14. 

SAVE THESE INSTRUCTIONS.

SAFETY WARNINGS

•  All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.
• 

The following conventions are used to indicate and classify precautions in this manual and on product safety labeling. Failure to 

observe precautions could result in injury to people or damage to property.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.  

Obey all safety messages that follow this symbol to avoid possible injury or death. 

 

This symbol is used to identify the need to wear

 

protective gloves.

Caution indicates a 

POTENTIALLY

 

hazardous situation, which, if not avoided, 

MAY

 result in minor or moderate injury.

Caution used without the safety alert symbol 

indicates a potentially hazardous situation, which, 

if not avoided, may result in property damage.

Warning indicates a 

POTENTIALLY

  

hazardous situation, which, if not avoided, 

COULD

 result in death or serious injury.

This symbol is used to identify an 

ULTRAVIOLET LIGHT

 hazard.

This symbol is used to identify an 

ELECTRICAL 

SHOCK

 or 

ELECTROCUTION

 hazard.

This symbol is used to identify the need to wear 

approved ultraviolet blocking eyewear.

This symbol is used to identify the need to wear approved 

ultraviolet blocking face shield.

This symbol is used to identify components which must 

not be disposed of in trash

Danger indicates an

 IMMINENTLY  

hazardous situation, which, if not avoided, 

 

WILL

 result in death or serious injury.

Summary of Contents for Sanidyne 40-0634A





















Reviews: