background image

3

SAFETY WARNINGS

All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.

The following conventions are used to indicate and classify precautions in this manual and on product safety 
labeling. Failure to observe precautions could result in injury to people or damage to property.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. 
Obey all safety messages that follow this symbol to avoid possible injury or death.  

Danger indicates an 

IMMINENTLY

hazardous situation, which, if not avoided, 

WILL

result in death or serious injury.   

Warning indicates a 

POTENTIALLY

hazardous situation, which, if not avoided, 

COULD

result in death or serious injury.

Caution indicates a 

POTENTIALLY

hazardous situation, which, if not avoided, 

MAY

result in minor or moderate injury.   

Caution used without the safety alert symbol indicates a potentially hazardous 
situation, which, if not avoided, may result in property damage.

This symbol/pictorial is used to identify an 

ELECTRICAL SHOCK

or 

ELECTROCUTION

hazard.

This symbol/pictorial is used to identify an 

ULTRAVIOLET LIGHT

hazard.

Product safety labels should be periodically inspected and cleaned, as necessary, to maintain good legibility. 
Always replace illegible safety labels. Contact factory to obtain replacement safety labels.

!

SAFETY INSTRUCTIONS

WARNING: To guard against injury, basic safety precautions should be observed, including the following:

1. Read and follow 

ALL

safety instructions.

2. Do not use this water purifier for other than its intended purpose as described in this manual.
3. Do not alter design or construction.
4.

DANGER: To prevent the risk of severe or fatal electrical shock, special precautions must be

taken since water is present near electrical equipment. Always disconnect power before performing 
any maintenance.

5.

WARNING: Avoid exposure to direct or strongly reflected germicidal ultraviolet rays.

Germicidal ultraviolet rays are harmful to the eyes and skin.

6. Intended for indoor use only. The water purifier should be protected from the elements and from 

temperatures below freezing.

7. Do not operate water purifier if power cord or plug is damaged.
8. Electrical power supplied, to the water purifier, 

MUST

match power requirements listed on the 

water purifier.

9. Plug the water purifier into an approved ground fault circuit interrupt (GFCI) receptacle.

10.

CAUTION: Do not operate without proper electrical ground.

11. Do not exceed water purifier’s maximum rated flow capacity.

12. Do not exceed maximum operating pressure of 100 PSI.
13. Read and follow all notices and warnings on the water purifier.
14.

SAVE THESE INSTRUCTIONS.

!

!

!

!

Summary of Contents for Mighty Pure MP13A





















Reviews: