Atlanta Attachment Company 1390BX Technical Manual & Parts Lists Download Page 23 | Manualshive

Page: 23 / 172

background image

Technical Manual & Parts Lists

15

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Machine Operation

Machine Start (Cold)

1. Turn the Main On/Off switch to the ON position. See Fig. 3.
2. Turn the Main Air valve to the ON position. The pressure gauge should
be set to 80 PSI. See Fig. 4.
3. Press the green POWER ON push button. See Fig. 5.
The Seal Bars begin to heat up at this point. It takes approx. 30 minutes to
get the Seal Bars to their operating temperature.
Note: The Standard machine Temperature Settings are:

Side Seal Bars - 325 ºF (w/o boot film)

Side Seal Bars - 345 ºF (w/ boot film)

Cross Seal Bar - 345 ºF

Note: Under the normal machine conditions, the start screen will appear on
the touch screen. When the green light on the light tower is on, the machine
has reached operating temperature and is ready to run. If the green light
does not illuminate, it usually indicates that one or more Emergency Stops
are not reset or other error condition exists. Refer to “Light Tower Indicator”
on page 24 of this manual for further light tower color explanation.

4. Wait for all three Seal Bars to heat up to their preset temperatures. It will
take approx. 20-30 minutes depending on the room temperature.

Note: The Seal Bars will not seal properly until they reach their proper
temperature.

After a short delay (approx. 5 sec.) the INPUT belts will turn on.
Machine is now ready for production.

5. Press the Start button on the touch screen. See Fig 6.

Machine Start (Warm)

1. Wait for all three Seal Bars to heat up to their preset temperatures. It
will take approx. 20-30 minutes depending on the room temperature.

Note: The Seal Bars will not seal properly until they reach their proper
temperature.

2. Press the Start button on the touch screen. See Fig 7.
After a short delay (approx. 5 sec.) the INPUT belts will turn on.
Machine is now ready for production.

Note: If the machine does not start and you do not get an error message
on the screen, refer to the LIGHT TOWER INDICATOR on page 24 of
this manual for additional information.

«
...
21
22
23
24
25
...
»

Summary of Contents for 1390BX













































































































































































Reviews:

No comments

Related manuals for 1390BX

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: Major Pages: 52

Brand: Task Force Tips Pages: 20

Brand: U-Line Pages: 9

Green Machine H-3518

Brand: U-Line Pages: 3

Brand: Sable Pages: 28

McDonnell & Miller PSE-800-M

Brand: Xylem Pages: 20

Brand: Qtx Pages: 6

Brand: Jäger Pages: 36

Brand: IMG STAGE LINE Pages: 12

Brand: Electro-Music Pages: 120

Brand: habitat et jardin Pages: 4

Brand: IntesisBox Pages: 2

Brand: Maquet Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands